Wirnet™ i-series

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Wirnet™ iFemtoCell-evolution: Connect to the gateway ======

===== Powering the iFemtoCell-evolution =====

Connect the AC/DC power supply to the barrel jack power connector.

Technical specifications for power supply:

{{:images:polarity.png?nolink|}}

  * Polarity: positive tip
  * Voltage: DC 12V
  * Current: 500mA
  * PCB connector - barrel jack (5.5mm sleeve, 2.5mm pin/tip)

{{ :images:ifevo_connect.png?nolink&500 |}}

<note warning>Take care to switch-off the gateway properly to avoid data loss (use the ''halt'' command or press on/off button during 3s).\\
The power supply is intended for indoor use only.</note>

===== SIM insertion =====

If 3G/4G cellular connection is used, insert USIM in dedicated holder before powering-up the gateway.

{{:images:ifevo_sim_insertion.png?nolink&200 |}}

===== Connect through the network =====

Please see the [[wiki:systeme_mana:connection_credentials|connection, login and credentials page]] for more information on how to connect to your iFemtocell-evolution.

===== Local connection (USB) =====

You can connect a PC directly to the iFemtocell-evolution with a USB cable. In this mode, the gateway will simulate an ethernet device.

  * In nominal case, after few seconds, your PC will obtain an IP address and you will be able to start a SSH client or HTTP connection on gateway IP 192.168.120.1.
  * In particular case you are using a DHCP server on your computer, gateway will directly obtain an IP address. A connection can then be done on this IP address.


{{:images:Ifemtocell_evo_USB_C_small.jpg?| }}

See [[wiki:systeme_mana:connection_credentials#default_password|here for more information]] about SSH/HTTP connection details.


===== Debug Probe =====

Wirnet™ Debug Probe is the only compatible debug probe.

==== Connection ====

Plug Wirnet Debug probe on your gateway Type-C connector from one side and on USB connector of your computer on the other side as explained in Wirnet Debug probe quickstart.

{{:images:ifevo_debug_probe.png?nolink&500|}}

Once plugged correctly:
  * Green equipment led on Debug probe should be ON (equipment «power» led remote display).
  * Serial port led (on PC side) should be ON (or blink if communication is on-going between equipment and terminal)


==== Windows installation ====

  - Download the [[http://www.ftdichip.com/Drivers/VCP.htm|ftdi drivers]] for the debug probe 
  - Install the drivers

==== Linux installation ====

On Linux, everything should work out of the box. The serial port will be located in ''/dev/ttyUSB*''.


==== Connection to the Wirnet™ iFemtocell-Evolution ====
  - Open a serial terminal (HyperTerminal, PuTTY, Teraterm, GNU screen, minicom, etc.)
  - Select the serial port created by the FTDI driver (usually: ''COM3'' on Windows, ''/dev/ttyUSB0'' on Linux)
  - Apply the following parameters to use your serial connection:
     * baud rate : ''115200''
     * data length : ''8''
     * parity : ''none''
     * stop bit : ''1''
     * flow control : ''none''
  - Enter your credentials in the command prompt:
     * login: ''root''
     * password: ''pdmk-$serialno''
''pdmk-**$serialno**'' is the default password on the gateway. See [[wiki:systeme_mana:connection_credentials#default_password|here for more information]]. In case of failure, request password to [[support@kerlink.fr]].
Wirnet™ i-series

User Tools

Site Tools

Page Tools
