Differences

This shows you the differences between two versions of the page.

--- wiki:quick_startup_guide [2017/11/07 11:34]
tda
+++ wiki:quick_startup_guide [2018/01/31 11:45] (current)
tda
@@ Line 1: / Line 1: @@
 ====== Quick startup guide ======
-===== Required software =====
+===== How to install packages for the RAN ? =====
-Wanesy RAN connectivity needs the latest version of the following packages installed on the gateway:
+For Wanesy RAN connectivity, we recommend to install the latest version of the packages specified in the compatibility matrix (depending of the RAN release version) that you can find here: [[wiki:releases|Software Releases]]:
-  * Keros firmware
+  * Firmware package
   * BSCC package
   * SNMP package
-  * Packet forwarder package
+  * HAL package
-  * OpenVPN package (contact  [[mailto:support@kerlink.fr|support@kerlink.fr]])
+  * Packet Forwarder package
+  * OpenVPN package
-These packages can be downloaded from the [[wiki:releases|Software Releases]] page.
+To obtain the specific OpenVPN package for your gateway, please contact [[mailto:support@kerlink.fr|support@kerlink.fr]]
+Install can be performed either over the network, either by USB.\\
+You need also a local debug link or open a SSH session in order to send commands to the gateway and get the feedback.
+Package installation procedure is described on the product dedicated wiki page :
+  * [[http://wikikerlink.fr/wirnet-ibts/doku.php?id=wiki:upgrade|Wirnet iBTS]]
+  * [[http://wikikerlink.fr/wirnet-ifemtocell/doku.php?id=wirnet-ifemtocell:software_updates|Wirnet iFemtoCell]]
+  * [[http://wikikerlink.fr/lora-station/doku.php?id=wiki:upgrade_legacy|Wirnet Station]]
-===== OpenVPN Package Installation =====
+We recommend to follow the procedure below :
-==== iBTS / iFemtoCell ====
+  - Install the firmware package
+  - Install RAN packages : BSCC / SNMP / OpenVPN
+  - Check the VPN connection to the RAN
+  - Install HAL & Packet Forwarder packages : LORA HAL / SPF
+  - Check Packet Forwarding
-The OpenVPN package can be installed on the sytem by the same manner as any other package.
+<note important>
+Note that for Step 4, you can install packages from the RAN Dashboard interface using the the Drag&Drop feature.\\
+Refer to the section [[http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:bsc|Software update]] to know how to proceed.
+</note>
-Package installation procedure is described on the product dedicated wiki page :
+\\
+===== How to update packages for the RAN ? =====
-  * [[http://wikikerlink.fr/wirnet-ibts/doku.php?id=wiki:upgrade|iBTS]]
+<note important>
-  * [[http://wikikerlink.fr/wirnet-ifemtocell/doku.php?id=wirnet-ifemtocell:software_updates|iFemtoCell]]
+Preconditions:
-  * [[http://wikikerlink.fr/lora-station/doku.php?id=wiki:upgrade|wirnet station]]
+Before proceeding to the update, check that all your software packages are at the software level (version number) indicated in the compatibility matrix:
+[[wiki:releases|Software Releases]]
+</note>
+There are 3 ways to update your gateway:
+  * <fc #4682b4>via the RAN Dashboard interface (recommended)</fc>
+  * <fc #4682b4>over the network</fc>
+  * <fc #4682b4>via an USB key</fc>
+=== Update via the Dashboard interface ===
+Since you are already connected to the RAN, you can update your packages through the Dashboard interface via the Drag&Drop area: refer to the
+[[http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:bsc|Software update]] page to know how to proceed.
+=== Update over the network or via USB ===
+Install the new version by following the procedure described above for packages installation.
+OpenVPN package does not need to be re-installed in the system.
+Refer to the specific Wiki to get details about the procedure to remove a package from the system.
+<note important>
+Upgrading the packet Forwarder will remove all your Packet Forwarder's configuration data (config.json)\\
+Please save it or copy files to a well-known location (ex /user/my_backup) before proceeding to the update
+</note>
+<note important>
+Take care if your Wirnet Station's firmware is **2.x** and if you choose to upgrate your gateway via a remote manner, you must install a specific dota to upgrade your firmware. Refer to the [[http://wikikerlink.fr/lora-station/doku.php?id=wiki:upgrade|Wirnet Station]] section to get some details about the procedure to follow.
+</note>
+\\
 ===== Checking configuration =====
-==== On the gateway ====
+You can either check all points in the [[ http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:checklist|checklist]]
+either check the 2 following points to go faster.
-In LoRa packet-forwarder configuration :
+\\
+==== Checking VPN connection to the RAN ====
+\\
-   * For wirnet station : ''/mnt/fsuser-1/spf/etc/local_conf.json''
+=== Via debug link or SSH access ===
-   * For wirnet iBTS : ''/user/spf2/etc/config.json''
-   * For wirnet iFemtoCell : ''/user/spf/etc/local_conf.json''
-following parameters can be checked :
+Type an  ''ifconfig'' command and check that the ''vpn0'' interface has been created.
+On failure, refer to the  [[ http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:troubleshooting|troubleshooting ]] section.
+=== Via the Dashboard interface ===
+Your gateway must be declared in an existing fleet (create it first if necessary) using its EUI in the [[http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:administration|administration]] menu.
+This EUI can be found in the field gateway_ID of the generated JSON file (you need obviously a local or remote access to the gateway):
+   * For Wirnet station : ''grep gateway_ID /mnt/fsuser-1/spf/etc/local_conf.json''
+   * For Wirnet iBTS : ''grep gateway_ID  /user/spf2/etc/config.json''
+   * For Wirnet iFemtoCell : ''grep gateway_ID  /user/spf/etc/local_conf.json''
+Once the station has been added to an existing fleet, select the BSC menu and select your fleet. [[http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:bsc]]\\
+\\
+The Gateway should appear in the list of stations and its status should be "Connected". Wait few minutes and force F5 page refresh if not the case.
+In case of persistent issue, refer to the [[ http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:troubleshooting|troubleshooting]] section.
+\\
+==== Checking Packet Forwarding ====
+\\
+=== Via debug link or SSH access ===
+Connect to the gateway via SSH command.
+Then, check LoRa packet-forwarder configuration file :
+   * For Wirnet station :    ''/mnt/fsuser-1/spf/etc/global_conf.json''
+   * For Wirnet iBTS :       ''/user/spf2/etc/config.json''
+   * For Wirnet iFemtoCell : ''/user/spf/etc/global_conf.json''
+Parameters to check are :
    * ''server_address'': lns (or "172.18.0.1" if you experience issues or if the support team asked you to do so)
@@ Line 46: / Line 125: @@
    * ''serv_port_down'': 1700
-==== On the dashboard ====
+Check packet forwarder logs:
+   * For Wirnet station :    ''/mnt/fsuser-1/spf/var/log''
+   * For Wirnet iBTS :       ''/user/spf2/var/log/''
+   * For Wirnet iFemtoCell : ''/user/spf/var/log''
-New gateways must be declared in an existing fleet (create it first if necessary), using their EUI.
-This EUI can be found in the field gateway_ID of the generated JSON file:
+=== Via the dashboard interface ===
-   * For wirnet station : ''grep -r gateway_ID /mnt/fsuser-1/spf/etc/local_conf.json''
+In the  [[http://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:administration|administration]] menu :
-   * For iBTS : ''grep -r gateway_ID  /user/spf2/etc/config.json''
-   * For iFemtoCell : ''grep -r gateway_ID  /user/spf/etc/local_conf.json''
+    * Declare a new cluster if the test cluster does not exist
+    * Declare a test endpoint in this cluster
+    * Select your gateway EUI in the BSC/Stations menu and copy it to the clipboard
+    * Select your gateway in the LNS/Stations menu using filtering function and paste EUI
+    * check traffic messages (Last Rx messages)

Wanesy™ Management Center (End Of Life)

User Tools

Site Tools

Differences

Page Tools