User Tools
wiki:quickstart
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:quickstart [2018/05/17 15:42] mpe |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Quick Start ====== | ||
| - | |||
| - | This section aims to guide a user through the main steps of the configuration of the SPN firmware. | ||
| - | In this quickstart, the user will start with a freshly installed software with no configuration and end with an end-device sending data to SPN. | ||
| - | |||
| - | Prerequisites: | ||
| - | * SPN is already installed on an iFemtoCell | ||
| - | * The SPN license file of this iFemtoCell | ||
| - | * The iFemtoCell is connected to a network with a __DHCP server__ and a __DNS server__ | ||
| - | * Chrome is used to connect to web interface | ||
| - | |||
| - | |||
| - | ===== Web interface login ===== | ||
| - | The home web interface is accessible at the following address: | ||
| - | ''http://klk-wifc-XXXXXX/'' | ||
| - | Where XXXXX are the 6 digits at the end of hostname/board id . | ||
| - | |||
| - | Example: | ||
| - | The address to be used with the iFemtoCell owning the following label is: ''http://klk-wifc-03002e/'' (case insensitive) | ||
| - | |||
| - | {{ :wiki:label_ifemtocell_v1.0.jpg?nolink&400 |}} | ||
| - | |||
| - | * Connect to the web interface | ||
| - | |||
| - | The default login/password are:\\ | ||
| - | user: ''spn''\\ | ||
| - | password: ''spnpwd'' | ||
| - | |||
| - | ===== License installation ===== | ||
| - | |||
| - | Installing the SPN software is not sufficient to use it. It also needs to be activated with a license file. | ||
| - | |||
| - | * Go to the //License// tab under the //Administration// menu. | ||
| - | * Either click on the panel and choose the license TXT file, or drag and drop it. | ||
| - | |||
| - | //Make sure that your license matches your firmware.// | ||
| - | * //V1 license file should be used with V1.x.x firmware.// | ||
| - | * //V2 license file should be used with V2.x.x firmware. // | ||
| - | |||
| - | //Licences can be opened with a text editor:// | ||
| - | * //V1 licenses look like this:// | ||
| - | <code> | ||
| - | 8d4222861dad7c24752aa6d3801e4017 | ||
| - | </code> | ||
| - | |||
| - | * //V2 licenses look like that:// | ||
| - | <code> | ||
| - | -----BEGIN SIGNATURE----- | ||
| - | q3JqyX09evkx8B3hrdS+5tEgOoViHR+zqn2fgcFwXZQmdps0D6wcMKUlWyKftUW2 | ||
| - | QgBXl2JgtfNKrYRQbgw7SPbmjrwPBIcVxrzlaqjIKLNc8DIDZ504ctwuakffgb45 | ||
| - | +XWiWA9X8q0jTcuG7KWkDyHSQHbMlGAX599mIKXx35/6hlkESKV1WU9ujHTZqBN3 | ||
| - | 6uVm8UQJh8lJi1nU9SNuCydthYbwqPApkOT9ueoAcGg+zSJFXxeVnwGBnR0g1TSr | ||
| - | mb2Y/Iu1C6oHECrqOh7w0ZZV8ZxSylkIjZaLJ72nqMkHMLxfw0Rcl80FrdcoRCFU | ||
| - | xmqKfWh95tinNCB/K7oCDA== | ||
| - | -----END SIGNATURE----- | ||
| - | -----BEGIN LICENSE----- | ||
| - | [license] | ||
| - | hardware_serial_number = 3901010E | ||
| - | expiration_date = 1621096442 | ||
| - | gateways_max_number = 1 | ||
| - | end_devices_max_number = -1 | ||
| - | -----END LICENSE----- | ||
| - | </code> | ||
| - | |||
| - | |||
| - | ===== Password update ===== | ||
| - | For security reasons, Kerlink strongly advises its customers to change the default password. | ||
| - | |||
| - | * Go to the //Station// tab under the //Administration// menu and change the password. | ||
| - | |||
| - | ===== Regional parameters configuration ===== | ||
| - | The region where the station will be used needs to be configured. | ||
| - | |||
| - | * Go to the //Region// menu and choose your region. | ||
| - | * Validate the modification with the //save configuration// button. | ||
| - | |||
| - | ===== Rx configuration ===== | ||
| - | The iFemtoCell cannot listen to every frequencies simultaneously. Up to 8 frequencies can be listened. | ||
| - | The frequencies to be listened need to be configured. | ||
| - | |||
| - | To understand how the frequency configuration works, it is necessary to know that the gateways' hardware contains two RF frontends. Each of these frontends has a 0.8 MHz Bandwidth. Thus, all 8 channels must be contained within these two 0.8 MHz intervals. | ||
| - | |||
| - | //Not all the channels are necessarily used.// | ||
| - | |||
| - | Example of typical configuration: | ||
| - | {{ :wiki:typical_rx_config_v1.1.png?nolink |}} | ||
| - | |||
| - | //All 8 frequencies can be contained within one 0.8MHz interval.// | ||
| - | |||
| - | {{ :wiki:one_bandwitdth_rx_config_v1.1.png?nolink |}} | ||
| - | |||
| - | * Go to the //Rx Configuration// menu and choose your region. | ||
| - | * Enter the center frequencies of both frontends. | ||
| - | * Enter the frequencies that your end-device uses. | ||
| - | * Validate the modification with the //save configuration// button | ||
| - | |||
| - | ===== End-device registration ===== | ||
| - | Before receiving data from the end-device, it first needs to be registered. | ||
| - | |||
| - | * Go to the //manage endpoints// tab under the //Endpoints// menu. | ||
| - | * Fill the information of your endpoint. //If you are not in Europe, you will probably have to use the Override default Rx parameters// | ||
| - | * Validate the end-device with the //add endpoint// button | ||
| - | |||
| - | ===== Data reception==== | ||
| - | The (basic) configuration is over. | ||
| - | * Go to the //Received data// menu. //You can refresh the received packets with the refresh button at the bottom right corner of the page.// | ||
wiki/quickstart.1526564527.txt.gz · Last modified: 2020/02/21 11:53 (external edit)
Page Tools
