User Tools
wiki:quickstart
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:quickstart [2020/02/21 12:16] ghi |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Quick Start ====== | ||
| - | |||
| - | This section aims to guide a user through the main steps of the configuration of the SPN firmware. | ||
| - | In this quickstart, the user will start with a freshly installed software with no configuration and end with an end-device sending data to SPN. | ||
| - | |||
| - | Prerequisites: | ||
| - | * SPN is already installed on an iFemtoCell | ||
| - | * The SPN license file of this iFemtoCell | ||
| - | * Chrome is used to connect to web interface | ||
| - | |||
| - | ===== Connection to the iFemtoCell ===== | ||
| - | |||
| - | |||
| - | ==== Ethernet or WiFi ==== | ||
| - | |||
| - | === SPN V1 === | ||
| - | |||
| - | To connect to the SPN for the first time, an Ethernet cable must be used. | ||
| - | |||
| - | === SPN V2 === | ||
| - | |||
| - | Since SPN V2, Ethernet and WiFi can be used to connect to the gateway. A WiFi access point is available at boot time on each iFemtoCell for one hour, broadcasting an SSID named after its serial number (klk-wifc-XXXXXX). It can only be used to access the SPN iFemtoCell's web interface, as it does not route traffic to anywhere and does not serve as an Internet wireless access point. | ||
| - | |||
| - | The passphrase to connect to this WiFi network is the Ethernet MAC address (it can be found on the Wirnet iFemtoCell label), in uppercase, without spaces between the digits, e.g. 7076FFYYYYYY. | ||
| - | |||
| - | Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal. | ||
| - | |||
| - | <note> | ||
| - | If ethernet is used your iFemtoCell SPN needs a DHCP server and a DNS server on the network to work. For both SPN V1&V2. | ||
| - | </note> | ||
| - | |||
| - | ===== Web interface login ===== | ||
| - | The home web interface is accessible at the following address: | ||
| - | ''http://klk-wifc-XXXXXX/'' | ||
| - | Where XXXXX are the 6 digits at the end of hostname/board id . | ||
| - | |||
| - | Example: | ||
| - | The address to be used with the iFemtoCell owning the following label is: ''http://klk-wifc-03002e/'' (case insensitive) | ||
| - | |||
| - | {{ :wiki:label_ifemtocell_v1.0.jpg?nolink&400 |}} | ||
| - | |||
| - | * Connect to the web interface | ||
| - | |||
| - | The default login/password are:\\ | ||
| - | user: ''spn''\\ | ||
| - | password: ''spnpwd'' | ||
| - | |||
| - | ===== License installation ===== | ||
| - | |||
| - | Installing the SPN software is not sufficient to use it. It also needs to be activated with a license file. | ||
| - | |||
| - | * Go to the //License// tab under the //Administration// menu. | ||
| - | * Either click on the panel and choose the license TXT file, or drag and drop it. | ||
| - | |||
| - | //Make sure that your license matches your firmware.// | ||
| - | * //V1 license file should be used with V1.x.x firmware.// | ||
| - | * //V2 license file should be used with V2.x.x firmware. // | ||
| - | |||
| - | //Licences can be opened with a text editor:// | ||
| - | * //V1 licenses look like this:// | ||
| - | <code> | ||
| - | 8d4222861dad7c24752aa6d3801e4017 | ||
| - | </code> | ||
| - | |||
| - | * //V2 licenses look like that:// | ||
| - | <code> | ||
| - | -----BEGIN SIGNATURE----- | ||
| - | q3JqyX09evkx8B3hrdS+5tEgOoViHR+zqn2fgcFwXZQmdps0D6wcMKUlWyKftUW2 | ||
| - | QgBXl2JgtfNKrYRQbgw7SPbmjrwPBIcVxrzlaqjIKLNc8DIDZ504ctwuakffgb45 | ||
| - | +XWiWA9X8q0jTcuG7KWkDyHSQHbMlGAX599mIKXx35/6hlkESKV1WU9ujHTZqBN3 | ||
| - | 6uVm8UQJh8lJi1nU9SNuCydthYbwqPApkOT9ueoAcGg+zSJFXxeVnwGBnR0g1TSr | ||
| - | mb2Y/Iu1C6oHECrqOh7w0ZZV8ZxSylkIjZaLJ72nqMkHMLxfw0Rcl80FrdcoRCFU | ||
| - | xmqKfWh95tinNCB/K7oCDA== | ||
| - | -----END SIGNATURE----- | ||
| - | -----BEGIN LICENSE----- | ||
| - | [license] | ||
| - | hardware_serial_number = 3901010E | ||
| - | expiration_date = -1 | ||
| - | gateways_max_number = 1 | ||
| - | end_devices_max_number = -1 | ||
| - | -----END LICENSE----- | ||
| - | </code> | ||
| - | |||
| - | |||
| - | ===== Password update ===== | ||
| - | For security reasons, Kerlink strongly advises its customers to change the default password. | ||
| - | |||
| - | * Go to the //Station// tab under the //Administration// menu and change the password. | ||
| - | |||
| - | ===== Regional parameters configuration ===== | ||
| - | The region where the station will be used needs to be configured. | ||
| - | |||
| - | * Go to the //Region// menu and choose your region. | ||
| - | * Validate the modification with the //save configuration// button. | ||
| - | |||
| - | ===== Rx configuration ===== | ||
| - | The iFemtoCell cannot listen to every frequencies simultaneously. Up to 8 frequencies can be listened. | ||
| - | The frequencies to be listened need to be configured. | ||
| - | |||
| - | To understand how the frequency configuration works, it is necessary to know that the gateways' hardware contains two RF frontends. Each of these frontends has a 0.8 MHz Bandwidth. Thus, all 8 channels must be contained within these two 0.8 MHz intervals. | ||
| - | |||
| - | //Not all the channels are necessarily used.// | ||
| - | |||
| - | Example of typical configuration: | ||
| - | {{ :wiki:typical_rx_config_v1.1.png?nolink |}} | ||
| - | |||
| - | //All 8 frequencies can be contained within one 0.8MHz interval.// | ||
| - | |||
| - | {{ :wiki:one_bandwitdth_rx_config_v1.1.png?nolink |}} | ||
| - | |||
| - | * Go to the //Rx Configuration// menu and choose your region. | ||
| - | * Enter the center frequencies of both frontends. | ||
| - | * Enter the frequencies that your end-device uses. | ||
| - | * Validate the modification with the //save configuration// button | ||
| - | |||
| - | ===== End-device registration ===== | ||
| - | Before receiving data from the end-device, it first needs to be registered. | ||
| - | |||
| - | * Go to the //manage endpoints// tab under the //Endpoints// menu. | ||
| - | * Fill the information of your endpoint. //If you are not in Europe, you will probably have to use the Override default Rx parameters// | ||
| - | * Validate the end-device with the //add endpoint// button | ||
| - | |||
| - | ===== Data reception==== | ||
| - | The (basic) configuration is over. | ||
| - | * Go to the //Received data// menu. //You can refresh the received packets with the refresh button at the bottom right corner of the page.// | ||
| - | * test | ||
wiki/quickstart.1582283788.txt.gz · Last modified: 2020/02/21 12:16 by ghi
Page Tools
