User Tools
wiki:quickstart
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:quickstart [2020/03/13 15:16] ghi |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Quick start ====== | ||
| - | |||
| - | This section aims to guide a user through the main steps of the configuration of the Wanesy SPN firmware in order to receive data from an end-device. | ||
| - | |||
| - | Prerequisites: | ||
| - | * Wanesy SPN installed on a gateway. | ||
| - | * Wanesy SPN license file available for the gateway. | ||
| - | * Google Chrome browser is used to connect to web user interface. | ||
| - | |||
| - | To use an end-device with Wanesy SPN, the end-device and the gateway need to use the same LoRa configuration. | ||
| - | Some parameters are common to the entire fleet and some parameters are end-device specific. | ||
| - | |||
| - | ===== Connection to the gateway ===== | ||
| - | |||
| - | Ethernet is available on all gateways but Wi-Fi only available on iFemtoCell model. | ||
| - | |||
| - | ==== Ethernet information ==== | ||
| - | |||
| - | If ethernet is used, the gateway needs DHCP and DNS servers on the network to work properly. | ||
| - | |||
| - | ==== Wi-Fi information ==== | ||
| - | |||
| - | On iFemtoCell gateway, Wi-Fi access point is available at boot time for one hour, broadcasting an SSID named after its serial number (''klk-wifc-XXXXXX''). It can only be used to access the Wanesy SPN iFemtoCell's web user interface (it does not route traffic to anywhere and does not serve as an Internet wireless access point) | ||
| - | |||
| - | The passphrase to connect to this Wi-Fi network is the Ethernet MAC address (it can be found on the Wirnet iFemtoCell label), in uppercase, without spaces between the digits, e.g. ''7076FFYYYYYY''. | ||
| - | |||
| - | Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal. | ||
| - | |||
| - | ===== Web user interface access ===== | ||
| - | |||
| - | The home web interface is accessible at the following address: | ||
| - | ^ Gateway model ^ Address ^ | ||
| - | | **Wirnet iFemtoCell** | ''http://klk-wifc-XXXXXX/'' | | ||
| - | | **Wirnet iStation** | ''http://klk-wiis-XXXXXX/'' | | ||
| - | | **Wirnet iFemtoCell-evolution** | ''http://klk-fevo-XXXXXX/'' | | ||
| - | Where ''XXXXXX'' are the last 6 digits of board id. | ||
| - | |||
| - | Example: | ||
| - | Address to be used with the gateway owning the following label: ''http://klk-wifc-03002e/'' (case insensitive) | ||
| - | |||
| - | {{.:..:images:ifemtocell_label.jpg?400|Board ID can be retrieved on gateway case}} | ||
| - | |||
| - | Once login screen displayed enter following login/password:\\ | ||
| - | user: ''spn''\\ | ||
| - | password: ''spnpwd'' | ||
| - | |||
| - | ===== License installation ===== | ||
| - | |||
| - | To have all the features of Wanesy SPN firmware, a license file is needed. | ||
| - | |||
| - | * Go to ''Administration => License'' menu | ||
| - | * Drag and drop license file or click on the panel to upload the license file | ||
| - | |||
| - | ===== Password update ===== | ||
| - | |||
| - | For security reasons, Kerlink strongly advises its customers to change the default password. | ||
| - | |||
| - | * Go to ''Administration => Gateway => Change password'' | ||
| - | * Update password | ||
| - | |||
| - | ===== Region configuration ===== | ||
| - | |||
| - | The region where the gateway will be used needs to be configured. | ||
| - | |||
| - | * Go to ''Configuration => Region'' menu and select the region | ||
| - | * Validate the modification with the ''Save configuration'' button | ||
| - | |||
| - | ===== Rx configuration ===== | ||
| - | |||
| - | Gateway hardware contains 2 RF radios (0.8 MHz bandwidth for each radio). 8 multi SF channels and 1 mono SF channel can be configured on these 2 radios. | ||
| - | |||
| - | Rx configuration example (all channels enabled and configured): | ||
| - | |||
| - | {{.:..:webui:rx_configuration.png|Rx configuration}} | ||
| - | |||
| - | * Go to the ''Configuration => Rx configuration'' menu | ||
| - | * Configure radio activation and frequency | ||
| - | * Configure channels activation and frequency used by end-device | ||
| - | * Validate the modification with the ''Save configuration'' button | ||
| - | |||
| - | ===== End-device registration and activation ===== | ||
| - | |||
| - | End-device must be registered before receiving any data | ||
| - | |||
| - | * Go to the ''Fleet => End-devices => Manage end-devices'' menu | ||
| - | * Fill the information of the end-device to register. ''Override default Rx parameters'' if needed | ||
| - | * Validate the end-device with the ''Add end-device'' button | ||
| - | |||
| - | ===== Received data ==== | ||
| - | |||
| - | * Go to ''Fleet => Received data'' to display Rx data sent by the registered end-device. Click on ''Refresh'' button if needed (bottom right corner of the page) | ||
wiki/quickstart.1584108991.txt.gz · Last modified: 2020/03/13 15:16 by ghi
Page Tools
