User Tools
wiki:resources_spn_firmware_2.0.3
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:resources_spn_firmware_2.0.3 [2018/05/07 17:22] dlr |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ======= iFemtoCell SPN firmware v2.0.3 (April 2018) ====== | ||
| - | |||
| - | <note warning>**__Breaking of compatibility__: license files**\\ | ||
| - | |||
| - | Due to the evolution of Wanesy SPN V2 software, licensing management modification leads to a break of compatibility with the license management of Wanesy SPN V1. | ||
| - | |||
| - | Wirnet iFemtoCell Wanesy SPN firmware **v2** must only be activated by a valid Wanesy SPN V2 license file. | ||
| - | |||
| - | Wanesy SPN license file provided with SPN version V1 will not allow to run the Wanesy SPN **v2** version, even if the V2 firmware can be installed (locked waiting V2 license). | ||
| - | |||
| - | Please contact [[ sales@kerlink.com |sales@kerlink.com ]] to order SPN V2 licenses before upgrading to Wirnet iFemtoCell SPN firmware **v2**. | ||
| - | |||
| - | License files SPN V2 are not compatible with Wirnet iFemtoCell SPN firmware V1 (v1.0.3 and V1.1.1). </note> | ||
| - | |||
| - | ===== Changes from 1.1.1 ===== | ||
| - | |||
| - | ==== New features ===== | ||
| - | |||
| - | * [LoRa] Listen Before Talk (LBT) for Japan and Korea. | ||
| - | * [Multi-gateways]: SPN can now receive/send LoRa frames from/to other SPN iFemtoCell, Wirnet station and Wirnet iBTS. | ||
| - | * [SMS interface]: New interface to : get Rx data, add Tx data, manage configuration, manage end-devices, update interface activation, manage gateways, get status, update confguration file. | ||
| - | * [System]: Retrieve send Tx data. | ||
| - | * [System]: Delete end-device fleet. | ||
| - | * [System]: Add OpenVPN. | ||
| - | * [System]: Add halt command (with restrictions). | ||
| - | * [System]: Reset configuration . | ||
| - | * [LOCAL FTP interface]: License management. | ||
| - | * [WEB interface]:End-device parameters edition. | ||
| - | * [WEB interface]: Download Open-VPN configuration. | ||
| - | * [USB interface]: Add Tx data withUSB key command. | ||
| - | |||
| - | ==== Evolutions ===== | ||
| - | |||
| - | * [LOCAL FTP interface]: The status file names now contain a OK/KO status. | ||
| - | * [USB interface]: The status file names now contain a OK/KO status. | ||
| - | * [USB interface]: move XXXXXXXX_password file. | ||
| - | * [System]: Remove rx2_frequency and rx2_datarate parameters from configuration. | ||
| - | * [System]: Change Tx data field order. | ||
| - | * [System]: Serial number now with 8 digits. | ||
| - | * [system]: LED behavior. | ||
| - | * [System]: Update license file format. | ||
| - | * [System]: Shut down WiFi administration interface after 1 hour. | ||
| - | |||
| - | ==== Restrictions ==== | ||
| - | |||
| - | * [System]: Wirnet iFemtoCell SPN pass on WiFi connection only if we unplug the ethernet wire. | ||
| - | * [System]: Cannot declare an OTAA end-device starting with multiple 0 (e.g. 0000000000112233) if an ABP end-device has the same name (00112233). | ||
| - | * [System]: End-devices sequence numbers are reset if the end-devices are restarted. | ||
| - | * [System]: getOpenVPNConfiguration returns only "enable". | ||
| - | * [System]: Halt on iFemtoCell SPN doesn't really stop the iFemtoCell. It reboots after a few seconds/minutes. | ||
| - | * [System]: Region configuration lost between version 1.1.1 and 2.0.0 for US gateways. | ||
| - | * [System]: Status is always "UNKNOWN" in the fleet. | ||
| - | * [System]: Cannot create end-device immediately after a switch from region Australia 915-928 to AS 923MHz. | ||
| - | * [System]: Received data are not correctly formated (no zero padding). | ||
| - | * [System]: When switched off, the WiFi radio power is not truly powered off. | ||
| - | * [LoRa]: Change of network_id do not reject frames of a mote that don't perform a new join. | ||
| - | * [LoRa]: FSK is not supported with data rate 7. | ||
| - | * [LoRa]: DR6 SF7-BW250 for RX2 data rate is not available for Asia and Japan Region. | ||
| - | * [LoRa]: MonoSF drift from radio x central frequency is reduce from 400kHz to 300kHz. | ||
| - | * [LoRa]: Possible to set Tx power higher than 23 dBm in Korea Rrgion. | ||
| - | * [Remote HTTP]: The push URL cannot contain any question mark sign, has to end with a slash, and it always has a suffix appended to what the user has entered. | ||
| - | * [WEB interface]: When the timezone is changed, a reboot is needed to apply the configuration in the log files. | ||
| - | * [WEB interface]: Network parameters are lost when a network interface is turned off on WEB interface. | ||
| - | * [WEB interface]: Reset configuration is too slow, nothing happens before 30s - 60s. | ||
| - | |||
| - | |||
| - | ===== Compatibility ===== | ||
| - | |||
| - | ====Hardware==== | ||
| - | * No known issues on various hardware product versions. | ||
| - | |||
| - | ====Software==== | ||
| - | * Compatible with Wirnet iFemtocell firmware, from version 3.0.0.. | ||
| - | * Compatible with Wirnet iFemtocell/SPN firmware version 1.0.3 and 1.1.1. | ||
| - | |||
| - | ===== Download ===== | ||
| - | |||
| - | __For SPN new installation only (no SPN firmware installed):__ \\ | ||
| - | {{ :wiki:liveburner_2.0.3-spn_klk-wifc.ipk |}} md5: ''e1bd24ba904baba5020d3d2f1a236950''. | ||
| - | |||
| - | __For SPN upgrade only (SPN firmware already installed):__ \\ | ||
| - | {{ :wiki:keros_2.0.3-spn_klk-wifc.ipk |}} md5:''14ce5c413c0adaa826fe39872a749358'' | ||
| - | |||
| - | __For SPN reinstallation and reset (SPN 2.0.3 firmware already installed):__ \\ | ||
| - | {{ :wiki:liveburner_2.0.3-spn_klk-wifc.ipk.gpg |}} md5:''616c6befac9c53d7e35b87bfdb5cbd81'' | ||
wiki/resources_spn_firmware_2.0.3.1525706526.txt.gz · Last modified: 2020/02/21 11:53 (external edit)
Page Tools
