Wanesy™ SPN (End Of Life)

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
{{ :images:spnbanner.png?nolink&300 |}}
====== Quick start Wanesy™ SPN======

===== Introduction =====

Check your license version

   SRVLIC-SPN00   SPN V1 for Wirnet Station
   SRVLIC-SPN01   SPN V1 for Wirnet iFemtoCell
   SRVLIC-SPN2*   SPN V2 for Wirnet iFemtoCell / iStation / iFemtoCell-Evolution
   


If you have SRVLIC-SPN01 SPN V1 for **Wirnet iFemtoCell** gateway you must use the following Wiki: [[https://wikikerlink.fr/wirnet-ifemtocell-spn/doku.php?id=home|Wirnet iFemtocell SPN]].

If you have SRVLIC-SPN00   SPN V1 for **Wirnet Station** gateway you must use the following Wiki: [[https://wikikerlink.fr/lora-iot-station-spn/doku.php?id=lorahome|IoT Station SPN]].

===== Documentation =====


  * Leaflet : {{ :media:Commercial_leaflet_Wanesy_SPN_V2.5.pdf |}}\\





===== Connection to the gateway =====

Ethernet is available on all gateways but Wi-Fi only available on iFemtoCell model.

==== Ethernet information ====

If ethernet is used, the gateway needs DHCP and DNS servers on the network to work properly.

==== Wi-Fi information ====

On iFemtoCell gateway, Wi-Fi access point is available at boot time for one hour, broadcasting an SSID named after its serial number (''klk-wifc-XXXXXX''). It can only be used to access the Wanesy SPN iFemtoCell's web user interface (it does not route traffic to anywhere and does not serve as an Internet wireless access point)

The passphrase to connect to this Wi-Fi network is the Ethernet MAC address (it can be found on the Wirnet iFemtoCell label), in uppercase, without spaces between the digits, e.g. ''7076FFYYYYYY''.

Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal.

==== Web user interface access ====

The home web interface is accessible at the following address:
^ Gateway model                   ^ Address                    ^
| **Wirnet™ iFemtoCell**           | ''http://klk-wifc-XXXXXX/'' |
| **Wirnet™ iStation**             | ''http://klk-wiis-XXXXXX/'' |
| **Wirnet™ iFemtoCell-evolution** | ''http://klk-fevo-XXXXXX/'' |
Where ''XXXXXX'' are the last 6 digits of board id.

Example: 
Address to be used with the gateway owning the following label: ''http://klk-wifc-03002e/'' (case insensitive)

{{:wiki:images:ifemtocell_label.jpg?400|Board ID can be retrieved on gateway case}}

Once login screen displayed enter following login/password:\\
user: ''spn''\\
password: ''spnpwd''

===== Firmware Installation =====

  * Wanesy SPN firmware installation: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:installation|click here]]
  * Wanesy SPN firmware upgrade: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:upgrade|click here]]
  * Wanesy SPN firmware uninstall: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:uninstall|click here]]




==== License installation ====

To have all the features of Wanesy SPN firmware, a license file is needed.

  * Go to ''Administration => License'' menu
  * Drag and drop license file or click on the panel to upload the license file

==== Password update ====


For security reasons, Kerlink strongly advises its customers to change the default password.

  * Go to ''Administration => Gateway => Change password''
  * Update password

==== Region configuration ====

The region where the gateway will be used needs to be configured.

  * Go to ''Configuration => Region'' menu and select the region
  * Validate the modification with the ''Save configuration'' button

==== Rx configuration ====

Gateway hardware contains 2 RF radios (0.8 MHz bandwidth for each radio). 8 multi SF channels and 1 mono SF channel can be configured on these 2 radios.

Rx configuration example (all channels enabled and configured):

{{.:..:webui:rx_configuration.png|Rx configuration}}
 
  * Go to the ''Configuration => Rx configuration'' menu
  * Configure radio activation and frequency
  * Configure channels activation and frequency used by end-device
  * Validate the modification with the ''Save configuration'' button

==== End-device registration and activation ====

End-device must be registered before receiving any data

  * Go to the ''Fleet => End-devices => Manage end-devices'' menu
  * Fill the information of the end-device to register. ''Override default Rx parameters'' if needed
  * Validate the end-device with the ''Add end-device'' button

==== Received data ===

  * Go to ''Fleet => Received data'' to display Rx data sent by the registered end-device. Click on ''Refresh'' button if needed (bottom right corner of the page)

===== Register to wiki update =====

You can now register to Wiki update notifications:
  - **Click** on the envelope icon (//Manage subscriptions//) on the right side of the page.
  - **Choose** your option and Subscribe.
  - **Check** your subscription by click again on the envelope icon.

{{:images:wiki_subscribe.png?nolink |}}
Wanesy™ SPN (End Of Life)

User Tools

Site Tools

Page Tools
