Wanesy™ SPN (End Of Life)

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== SPN firmware v2.1.2 (February 2020) ======

===== Changes from 2.0.3 =====

==== New features ====

  * Compatible with Wirnet **iFemtoCell-evolution** gateway
  * Compatible with Wirnet **iStation** gateway
  * **Node-RED** available
  * Support of **Fujisoft FS040U dongle**

==== Evolutions ====

  * Web user interface features fit to licence
  * No more restrictions on SSH access

==== Bug fixes ====

  * [SMS utils] SMS: multiple answers received
  * [Web user interface] Crash with web user interface
  * [Remote HTTP] Relax the validation rules to the push URL
  * [System/Wi-Fi] Support for spaces in WPA PSK

==== Restrictions ====

  * [System]: Wirnet iFemtoCell SPN pass on WiFi connection only if we unplug the ethernet wire.
  * [System]: getOpenVPNConfiguration returns only “enable”.
  * [System]: Halt on iFemtoCell SPN doesn't really stop the iFemtoCell. It reboots after a few seconds/minutes.
  * [System]: When switched off, the WiFi radio power is not truly powered off.
  * [LoRa]: Cannot create end-device immediately after a switch from region Australia 915-928 to AS 923MHz.
  * [LoRa]: Status is always “UNKNOWN” in the fleet.
  * [LoRa]: Cannot declare an OTAA end-device starting with multiple 0 (e.g. 0000000000112233) if an ABP end-device has the same name (00112233).
  * [LoRa]: End-devices sequence numbers are reset if the end-devices are restarted.
  * [LoRa]: Change of network_id do not reject frames of a end-device that don't perform a new join.
  * [LoRa]: FSK is not supported with data rate 7.
  * [LoRa]: DR6 SF7-BW250 for RX2 data rate is not available for Asia and Japan Region.
  * [LoRa]: MonoSF drift from radio x central frequency is reduce from 400kHz to 300kHz.
  * [LoRa]: Possible to set Tx power higher than 23 dBm in Korea Region.
  * [WEB user interface]: When the timezone is changed, a reboot is needed to apply the configuration in the log files.
  * [WEB user interface]: Network parameters are lost when a network interface is turned off on WEB interface.
  * [WEB user interface]: Reset configuration is too slow, nothing happens before 30s - 60s.

===== Compatibility =====

==== Hardware ====

  * No known issues on various hardware product versions

==== Software ====

^ Gateway model                   ^ KerOS firmware version ^ SPN firwmare version ^
| **Wirnet iFemtoCell**           | From 3.1.14            | 2.0.3                |
| **Wirnet iStation**             | From 4.2.2             | Not applicable       |
| **Wirnet iFemtoCell-evolution** | From 4.2.2             | Not applicable       |

==== LoRaWAN ====

  * Compatible with LoRaWAN Specification V1.0.2
  * Compatible with LoRaWAN Regional Parameters V1.1

===== Download =====

__To install from SPN with data loss (recommended) (**SPN FW already installed**):__\\
{{.:liveburner_2.1.2-spn_klk-wifc.ipk.gpg}} md5: ''518611b4f1f97fc7b7bb105703325ae4''.

__To install from SPN without data loss (**SPN FW already installed**):__\\
{{.:fwupgrade_2.1.2-spn_klk-wifc.ipk.gpg}} md5:''8546dee6f19773942987a83f12ec7559''

__To install from KerOS (**SPN FW not installed yet**):__\\
{{.:liveburner_2.1.2-spn_klkgw-signed.ipk}} md5:''483a91bdce2c2b6328cb45fe7d99d17b''



**To check MD5 you can use Powershell command below :**

//Get-FileHash liveburner_2.1.2-spn_klkgw-signed.ipk -Algorithm MD5 //
Wanesy™ SPN (End Of Life)

User Tools

Site Tools

Page Tools
