Differences

This shows you the differences between two versions of the page.

--- wiki:firmware:installation [2020/04/28 09:00]
mbi [Wanesy SPN firmware installation]
+++ wiki:firmware:installation [2023/01/24 14:40] (current)
rco [With web interface recommended]
@@ Line 1: / Line 1: @@
-====== Wanesy SPN firmware installation ======
+====== Wanesy™ SPN firmware installation from KerOS firmware ======
-By default, Wanesy SPN firmware is not installed on Kerlink gateways. Wanesy SPN can be installed from these versions of KerOS:
+By default, Wanesy SPN firmware is not installed on Kerlink gateways. Therefore, to install the Wanesy SPN the following steps are required:
+  - Check the firmware version of the gateway
+  - If the firmware is not the expected one, upgrade it
+  - Upgrade SPN firmware via Web Interface, SSH or by USB
+<note important>
+Once Wanesy SPN firmware installed, gateway can be configured with web user interface (recommended) or other [[.:..:interfaces:interfaces|interfaces]]
+</note>
+===== Firmware version check =====
+Gateway has no default IP address. It is recommended to connect the gateway to a network using a DHCP server.
+==== With web interface "recommended" ====
+  * Connect to the web interface of your gateway: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:webui#connect_to_the_web_interface|click here]]
+<note important>For iFemtoCell, web interface password changed between version 3.3.3 and 3.4.3. Products leaving the warehouses could be in different versions. If the default password ''pwd4admin'' does not worked, try ''admin''.</note>
+  * Once connected to the web interface, go in the overview panel and check the firmware version in the "Information" section.
+  * Wanesy SPN can be installed from these versions of KerOS:
 ^ Gateway model                   ^ KerOS version    ^
@@ Line 8: / Line 30: @@
 | **Wirnet iFemtoCell-evolution** | 4.2.1 and above  |
-Therefore, to install the Wanesy SPN the following steps are required:
-  - Connect to the gateway using SSH
-  - Check the firmware version of the gateway
-  - If the firmware is not the expected one, upgrade it
-  - Upgrade firmware via SSH or via USB
-<note important>
+<note warning>Installation of SPN firmware from version 5.X is not possible. You will have to downgrade from 5.X to 4.3.3-2. You can download the firmware 4.3.3-2 on [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:firmware:lastversion#download|this page]]</note>
-Once Wanesy SPN firmware installed, gateway can be configured with web user interface (recommended) or other [[.:..:interfaces:interfaces|interfaces]]
-</note>
-===== SSH connection =====
+  * If the firmware is not the expected one, upgrade it.
+    *iFemtoCell: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:quickstart:quickstart_ifemto#firmware_update_and_configuration|click here]]
+    *iFemtoCell-evolution: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:quickstart:quickstart_ifevo#firmware_update_and_configuration|click here]]
+    *iStation: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:quickstart:quickstart_istation#firmware_update_and_configuration|click here]]
-Gateway has no default IP address. It is recommended to connect the gateway to a network using a DHCP server. Gateway IP address is needed to connect to it. (Contact your network administrator to get gateway IP address).
-  - Start a ssh client (for example: TeraTerm or Putty on Windows)
+==== With SSH connection ====
-  - Connect to the gateway with the following configuration:
+++++ click here|
+  * Start a ssh client (for example: TeraTerm or Putty on Windows)
+  * Connect to the gateway with the following configuration:
      * address: IP of your gateway
      * port: ''22''
@@ Line 32: / Line 53: @@
 {{.:..:images:ifemtocell_label.jpg?400|Board ID can be retrieved on gateway case}}
-===== KerOS firmware version check =====
+  * Once connected to the gateway, use the command below to get your firmware version:
-Once connected to the gateway, use the command below to get your firmware version:
 <code bash>
 cat /tmp/sys_startup_status.json | grep "sw_version"
 </code>
-An output similar to the following will be displayed:
+  * Wanesy SPN can be installed from these versions of KerOS:
-^ Gateway model                   ^ KerOS version check   ^
+^ Gateway model                   ^ KerOS version    ^
-| **Wirnet iFemtoCell**           | ''"sw_version": "3.1.14_20171019161710"'' |
+| **Wirnet iFemtoCell**           | 3.1.14 and above |
-| **Wirnet iStation**             | ''"sw_version": "4.1.6_20190829151113"'' |
+| **Wirnet iStation**             | 4.1.6 and above  |
-| **Wirnet iFemtoCell-evolution** | ''"sw_version": "4.2.1_20191209105655"'' |
+| **Wirnet iFemtoCell-evolution** | 4.2.1 and above  |
-If the firmware is not the expected one, upgrade it. (Refer to [[https://wikikerlink.fr/wirnet-productline/doku.php|Wirnet Productline wiki]]. Contact [[support@kerlink.fr]] to get access if needed)
+  * If the firmware is not the expected one, upgrade it.
+    *iFemtoCell: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:quickstart:quickstart_ifemto#firmware_update_and_configuration|click here]]
+    *iFemtoCell-evolution: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:quickstart:quickstart_ifevo#firmware_update_and_configuration|click here]]
+    *iStation: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:quickstart:quickstart_istation#firmware_update_and_configuration|click here]]
+++++
 ===== Wanesy SPN firmware installation =====
-The firmware update can be done by SSH or USB
+The firmware update can be done by Web interface, SSH or USB
+==== Software update over Web interface "recommended"====
+  - Download the firmware from [[wiki:support:resources|Resources]] page. The firmware can be download in the download section of the firmware delivery note. The file is named liveburner_X.X.X-spn_klkgw-signed.ipk.
+  - Connect to your gateway web interface
+  - Go in the "Administration" and "Update" Menu
+  - Drag & drop your SPN ipk file and click on UPDATE GATEWAY.
+  - A reboot is required to finalize the update, click on REBOOT GATEWAY.
+  - To use fix IP address check [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:webui:administration:network#ethernet_configuration_fixed_ip_address|Fixed IP]]
+<note important>
+Upgrade process will take a few minutes and reboot the gateway multiple times. Web user interface will be up and running when the left LED will be lit in green
+</note>
-==== SSH ====
+==== With SSH connection ====
+++++ click here|
   - Download the firmware from the [[.:..:support:resources|resources]] page
@@ Line 69: / Line 108: @@
 </note>
-==== USB ====
+++++
-=== Overview ===
+==== With USB ====
+++++ click here|
+**Overview**
   - Download the firmware from [[.:..:support:resources|resources]] page
@@ Line 85: / Line 127: @@
 </note>
-=== Specific files ===
+**Specific files**
-== usbkey.txt ==
+  * usbkey.txt
 ''usbkey.txt'' is a security file. It includes the password of **usbuser** user. \\
@@ Line 96: / Line 139: @@
 Here is an example of this file for 4 boards (010001 / 020056 / 040001 / 092356): \\
 First board has a generic password and 3 others have a "serial-based" modified password ("<serial>_usbkey") \\
+Link below to download usbkey.txt file
 <file text usbkey.txt>
 USBklkPassword
@@ Line 104: / Line 150: @@
 </file>
-== usb.autorun ==
+  * usb.autorun
 ''usb.autorun'' is a script automatically executed by the board if the ''usbkey.txt'' file includes a correct password.
 The following script is used to deploy the Wanesy SPN firmware. Copy this script in a file named ''usb.autorun''.
+Link below to download usb.autorun file
 <file bash usb.autorun>
@@ Line 216: / Line 264: @@
 set_led "timer" 100 100
 </file>
+++++
 ===== Wanesy SPN License installation =====
 Once the Wanesy SPN firmware is running, the license file needs to be installed in order to configure and use the SPN software. The [[.:..:introduction:quickstart|quick start]] page will guide you through these steps.

Wanesy™ SPN

User Tools

Site Tools

Differences

Page Tools