This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
wiki:firmware:lastversion [2021/06/29 11:06] mbi |
wiki:firmware:lastversion [2022/03/22 16:47] gat |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Wanesy Wave firmware v1.9.0 (May 2021) ====== | + | ====== Wanesy Wave firmware v2.1.0 (March 2022) ====== |
===== Changes from previous version ===== | ===== Changes from previous version ===== | ||
==== New features ==== | ==== New features ==== | ||
- | * No new feature in this release | + | * Dwell Time Applicative Configuration (AS923 only) |
- | + | ||
- | ==== Evolutions==== | + | |
- | * Asset tracking: improve BLE scan robustness | + | |
- | * Maximize Wi-Fi STM32 FW update success | + | |
- | * Earlier initialization of critical GPIOs | + | |
===== Restrictions ===== | ===== Restrictions ===== | ||
- | * Firmware upgrade procedure must respect specific order described in section below | + | * If the installed firmware is 1.8.0 or lower, firmware upgrade procedure must respect specific order described in section below. |
Line 32: | Line 27: | ||
=== Software === | === Software === | ||
- | * STM32 MCU firmware Ver. 1.9.0 | + | * STM32 MCU firmware Ver. 2.1.0 |
- | * ESP32 MCU firmware Ver. 1.9.0 | + | * ESP32 MCU firmware Ver. 2.1.0 |
Line 54: | Line 49: | ||
==== Wi-Fi: firmware update ==== | ==== Wi-Fi: firmware update ==== | ||
+ | === Installed firmware is v1.9.0 or higher version === | ||
+ | |||
+ | Regular firmware update can be followed (update ESP32 first), please read {{:documentation:E-CON-Wanesy_Wave_FW_Update_WiFi_V1.2.pdf |}} available in the [[wiki:setup:setup_wave|Wanesy™ Wave Setup: Documentation]] section. | ||
+ | |||
+ | === Installed firmware is v1.8.0 or lower version === | ||
+ | |||
+ | If the installed firmware is v1.8.0 or lower version, firmware update procedure must respect the specific order described below (update STM32 first): | ||
<note important> | <note important> | ||
- | Firmware update procedure must respect the specific order described below (update STM32 first): | ||
^ steps ^ STM32 version ^ ESP32 version ^ SSID ^ Actions ^ | ^ steps ^ STM32 version ^ ESP32 version ^ SSID ^ Actions ^ | ||
- | | #1 | 1.8.0 | 1.8.0 | wave_xxxx | Place product away from wall or table (ie. perpendicular is OK, parallel is KO)| | + | | #1 | v1.7.0/v1.8.0 | v1.7.0/v1.8.0 | optout_klk/wave_xxxx | Place product away from wall or table (ie. perpendicular is OK, parallel is KO)| |
- | |:::|:::|:::|:::|Upload STM32 V1.9 image| | + | |:::|:::|:::|:::|Upload STM32 v2.0.1 image| |
|:::|:::|:::|:::|Wait until green LED is back ON (ie. no longer blinking)| | |:::|:::|:::|:::|Wait until green LED is back ON (ie. no longer blinking)| | ||
- | | #2 | 1.9.0 | 1.8.0 | wave_xxxx | Verify STM32 version in device_info.txt file | | + | | #2 | v2.0.1 | v1.7.0/v1.8.0 | optout_klk/wave_xxxx | Verify STM32 version in device_info.txt file | |
- | |:::|:::|:::|:::|Upload ESP32 V1.9 image| | + | |:::|:::|:::|:::|Upload ESP32 v2.0.1 image| |
- | | #3 | 1.9.0 | 1.9.0 | wave_xxxx | Verify ESP32 version in esp32_version.txt file| | + | | #3 | v2.0.1 | v2.0.1 | wave_xxxx | Verify ESP32 version in esp32_version.txt file (displayed version is 2.0.0)| |
</note> | </note> | ||
- | * **Wanesy Wave 868**: {{ :wiki:resources:wifiupdate_wanesywave_eu868_v1.9.0_20210503_revs_cde.zip |}} | + | * **Wanesy Wave 868**: {{ :wiki:resources:wifiupdate_wanesywave_eu868_v2.1.0_20220303_revs_cde.zip |}} |
- | * STM32 file: ''stm32_wanesywave_EU868_v1.9.0_DAcde.kbin'' (md5: 9e6de37facb753162057d201e870e058). | + | * STM32 file: ''stm32_wanesywave_EU868_v2.1.0_DAcde.kbin'' (md5: 1597e8adef1b3b8d45e2cdc188726e5d). |
- | * ESP32 file: ''esp32_firmware_v1.9.0.bin'' (md5: fdff27fec5444d500745e962057efd46). | + | * ESP32 file: ''esp32_firmware_v2.1.0.bin'' (md5: 4d59916be12171d75e225273f130d752). |
- | * **Wanesy Wave 915**: {{ :wiki:resources:wifiupdate_wanesywave_us915_v1.9.0_20210503_revs_cdef.zip |}} | + | * **Wanesy Wave 915**: {{ :wiki:resources:wifiupdate_wanesywave_us915_v2.1.0_20220303_revs_cdef.zip |}} |
- | * STM32 file: ''stm32_wanesywave_US915_v1.9.0_DBcdef.kbin'' (md5: 35125aa8baf5555ed3e61e5be3882b22). | + | * STM32 file: ''stm32_wanesywave_US915_v2.1.0_DBcdef.kbin'' (md5: b1025f968e6c07ff2aeb4b69ef774295). |
- | * ESP32 file: ''esp32_firmware_v1.9.0.bin'' (md5: fdff27fec5444d500745e962057efd46). | + | * ESP32 file: ''esp32_firmware_v2.1.0.bin'' (md5: 4d59916be12171d75e225273f130d752). |
==== Wi-Fi: region configuration ==== | ==== Wi-Fi: region configuration ==== | ||
Line 86: | Line 87: | ||
===== History ===== | ===== History ===== | ||
+ | * 2.1.0 (March 2022): | ||
+ | * Dwell Time Applicative Configuration | ||
+ | * 2.0.1 (October 2021): | ||
+ | * BLE Asset Monitoring | ||
+ | * LoRaWan region setting resilient to factory reset | ||
* 1.9.0 (May 2021): | * 1.9.0 (May 2021): | ||
* Improve BLE scan robustness | * Improve BLE scan robustness |