Wanesy™ Wave

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Wanesy Wave firmware v1.8.0 (Feb. 2021) ======

===== Changes from previous version =====

==== New features ====

  * Support of multiple regional parameters: EU868, IN865, US915, AS923, AU915.
  * Dynamic configuration of region.
  * Use unconfirmed TX on LoRaWAN services.
  * Add possibility to change LoRaWAN frame period by configuration.
  * Introducing the CBOR configuration file device.cfg, to get and post parameters values.
  * Add UUID iBeacon filter.
  * Possibility to identify BLE Tags with MAC address or Major/Minor.
  * Wi-Fi updates over HTTP.
  * Wi-Fi access point SSID based on EUI.
  * Limit duration of Wi-Fi access point availability to 45 cycles of BLE scan period.
  * Add control of limit values for parameters.


==== Evolutions====

  * Avoid erroneous CBOR frame sent sometimes.
  * Major/minor configuration is now persistant after a power cycle.

===== Restrictions =====

   * Optout_klk SSID is used on the first boot after a factory reset command.
   * Switching filter (mac address or major/minor ) can stop BLE radio transmission. Workaround is to trigger a remote reboot command or manual reboot.
   * During configuration update, out of range values are replaced by "0". 


===== Firmware =====

==== Compatibility ====

=== Hardware ===

This release is compatible with the following Wanesy Wave revision:

  * **Wanest Wave 868**:
    * Fully compatible with Wanesy Wave Board ID xxxDAcxxxxxx, xxxDAdxxxxxx, xxxDAexxxxxx.
  * **Wanesy Wave 915**:
    * Fully compatible with Wanesy Wave Board ID xxxDBcxxxxxx, xxxDBdxxxxxx, xxxDBexxxxxx, xxxDBfxxxxxx .


=== Software ===

  * STM32 MCU firmware Ver. 1.8.0
  * ESP32 MCU firmware Ver. 1.8.0


==== Delivery ====

<note important>
The firmware is released in two files: __STM32 MCU__ firmware binary 'part' file and __ESP32 MCU__ firmware binary file.\\
</note>

__STM32 MCU :__ \\
To update the firmware, follow instruction on the Firmware update section of the Setup page: [[wiki:setup:setup_wave#firmware_update|click here]].

__ESP32 MCU:__ \\
To update the firmware, follow instruction on the Firmware update section of the Setup page: [[wiki:setup:setup_wave#firmware_update|click here]].



===== Download =====

==== Wifi update ====

  * **Wanesy Wave 868**: {{ :wiki:resources:wifiupdate_wanesywave_eu868_v1.8.0_20210205_revs_cde.zip |}}
    * STM32 part file: ''stm32_wanesywave_EU868_v1.8.0_DAcde.kbin'' (md5: 0215506241d1f5d5451f63933b7c6e67).
    * ESP32 file: ''esp32-firmware_v1.8.0.bin'' (md5: e6306fdff81e62ebdb6d00690ae3de6a).

  * **Wanesy Wave 915**: {{ :wiki:resources:wifiupdate_wanesywave_us915_v1.8.0_20210205_revs_cdef.zip |}}
    * STM32 part file: ''stm32_wanesywave_US915_v1.8.0_DBcdef.kbin'' (md5: 42692f4f3dab6bdefdb1fbb712453cf5).
    * ESP32 file: ''esp32_firmware_v1.8.0.bin'' (md5: e6306fdff81e62ebdb6d00690ae3de6a).


<note warning>Once installed, downgrade to version v1.7.0 is disapproved by Kerlink. </note>
===== History =====
   * 1.8.0 (February 2021):
    * Support of multiple regional parameters.
    * Use unconfirmed TX on LoRaWAN services.
    * Wi-Fi update over HTTP.
    * Access Point SSID personal identification based on EUI.
    * Limit duration of Wi-Fi access point availability.
   * 1.7.0 (June 2020):
    * Initial release for Wanesy Wave.
Wanesy™ Wave

User Tools

Site Tools

Page Tools
