Wanesy™ Wave

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Setup of Wanesy™ Wave ======


===== Documentation =====



  * Leaflet: {{:documentation:Kerlink_Wanesy-Wave-Commercial-Leaflet_v1.5.pdf |}}\\
  * Quickstart guide: {{:documentation:Kerlink_Wanesy-Wave_Quick-start-guide_v1.2.pdf |}}\\
  * Technical Product description: {{:documentation:Kerlink_Wanesy-Wave_Technical Product_Description_v1.4.pdf |}}\\
  * Interface documentation: Information currently available in the {{:documentation:e-con-wanesy_wave_interfaces-v1.0.pdf | e-con-wanesy_wave_interfaces-v1.0.pdf }}. \\
  * WiFi update: {{:documentation:e-con-wanesy_wave_fw_update_wifi_v1.1.pdf |}}\\
 

===== Connection to the LoRaWAN network =====

The Wanesy Wave is a Class A LoRaWAN end-device. OTAA (Over-The-Air Activation) join method is supported. 

The connection of the Wanesy Wave to a LoRaWAN network can be done by following steps below:
  - Retrieve the Wanesy Wave LoRaWAN credentials (DevEUI, AppEUI, AppKey). Those can be requested to support@kerlink.fr by providing the Wanesy Wave "Product ID".
  - Declare the Wanesy Wave on the LoRa Network Server (OTAA join procedure).
  - Install the Wanesy Wave in a LoRaWAN gateway coverage field, properly configured with the LoRa Network Server.
  - Plug the micro USB power supply in the Wanesy Wave micro USB connector.
  - Check the green LED is static (power supply presence).
  - Check the red LED is static at startup.
  - The red LED will be switched off once the Wanesy Wave has join the LoRaWAN Network.
  - Default application is running and a LoRaWAN™ frame is sent every 40 seconds or more if there are new BLE iBeacon data available.

===== Configuration =====

  * Remote configuration method and parameters are described in the Interface documentation available in the Documentation section of this page: [[wiki:setup:setup_wave#documentation|click here]].
  * Default configuration is described in the Interface documentation available in the Documentation section of this page: [[wiki:setup:setup_wave#documentation|click here]].
  * To reset the Wanesy Wave settings, see the FAQ chapter "How to reset the Wanesy Wave settings":  [[wiki:support:faq#how_to_reset_the_wanesy_wave_settings|click here]]\\


===== Interface =====

  * LoRaWAN up and down messages payloads are described in the Interface documentation available in the Documentation section of this page: [[wiki:setup:setup_wave#documentation|click here]].
===== LoRaWAN protocol =====

  * Kerlink is a member of LoRa Alliance and the Kerlink end-device Wanesy Wave is compatible with LoRaWAN® specifications V1.0.2 and LoRaWAN® Regional Parameters v1.0.2rB.
  * For more information about LoRaWAN network protocol, please contact the LoRa Alliance and request LoRaWAN specifications : [[https://lora-alliance.org/lorawan-for-developers]]

===== Firmware update =====

==== Check the firmware version:====
  * Use the FAQ chapter "How to read the software version":  [[wiki:support:faq#how_to_read_software_version|click here]]\\

==== Download the latest firmware version:====
  * Firmware update files are available into the dedicated firmware release version pages, listed on the [[wiki:resources:resources|Resources]] page: [[wiki:resources:resources|click here]].
  
==== Update the firmware ====

=== Wi-Fi firmware update ===

  * Wi-Fi firmware update is the preferred method.
  * Please refer to proper documentation //Wi-Fi update// available in the //Documentation// section: [[wiki:setup:setup_wave#documentation|click here]].

=== LoRaWAN FUOTA update ===

  * FUOTA is the acronym for Firmware Update Over-The-Air.
  * LoRaWAN FUOTA stack is available on Wanesy Wave. 
  * This type of firmware update requires the use of a compliant server (please contact the LoRa Alliance and request LoRaWAN specifications : [[https://lora-alliance.org/lorawan-for-developers]]).


===== Register to wiki update notifications =====

You can now register to Wiki update notifications:
  - **Click** on the envelope icon (//Manage subscriptions//) on the right side of the page.
  - **Choose** your option and Subscribe.
  - **Check** your subscription by click again on the envelope icon.

{{:images:wiki_subscribe.png?nolink |}}


===== What to do when assistance is needed? =====

  * **Read** the Frequently Asked Questions in this wiki: [[wiki:support:faq|click here]].

  * The answer is not under [[wiki:support:faq|frequently asked questions]]? 
     * => use Kerlink ticketing tool for customer support: [[http://otrs.kerlinkm2mtechnologies.com/customer.pl| OTRS ]]
Wanesy™ Wave

User Tools

Site Tools

Page Tools
