wiki:ibts:connect_ibts
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
wiki:ibts:connect_ibts [2019/09/25 15:27] ghi created |
wiki:ibts:connect_ibts [2020/09/22 14:44] (current) ghi |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Wirnet™ iBTS: Connect to the gateway ====== | ====== Wirnet™ iBTS: Connect to the gateway ====== | ||
| - | <note tip>Any questions on the product or accessories: please read the [[resources#documentations|Installation and Maintenance manual]].</note> | + | <note tip>Any questions on the product or accessories: please read the [[wiki:quickstart:quickstart_ibts#documentation|Installation and maintenance manual]].</note> |
| To connect to the Wirnet™ iBTS gateway, the following accessories are needed: | To connect to the Wirnet™ iBTS gateway, the following accessories are needed: | ||
| Line 18: | Line 18: | ||
| ===== Power supply the gateway ===== | ===== Power supply the gateway ===== | ||
| - | For the following points, detailed instructions are available in the Wirnet™ iBTS "Installation and Maintenance manual" of the [[resources|resources]] page.\\ There are two ways to power on the Wirnet™ iBTS: | + | For the following points, detailed instructions are available in the Wirnet™ iBTS "Installation and Maintenance manual" of the [[wiki:quickstart:quickstart_ibts#documentation|iBTS setup]] page.\\ There are two ways to power on the Wirnet™ iBTS: |
| * **Connect** the PoE output connector to the LAN port located on the bottom side of the CPU module. The RJ45 connector can be inserted directly to the gateway using a specific cable gland. | * **Connect** the PoE output connector to the LAN port located on the bottom side of the CPU module. The RJ45 connector can be inserted directly to the gateway using a specific cable gland. | ||
| Line 39: | Line 39: | ||
| ===== Connect through the network ===== | ===== Connect through the network ===== | ||
| - | Please see the [[wiki:connection_credentials|connection, login and credentials page]] for more information on how to connect to your iBTS. | + | Please see the [[wiki:systeme_mana:connection_credentials|connection, login and credentials page]] for more information on how to connect to your iBTS. |
| - | ===== Local connection ===== | + | ===== Local connection (LOCAL Ethernet) ===== |
| - | If you do not use yet backhaul Ethernet port, you can connect a PC directly to the iBTS with a cable to its LOCAL Ethernet port. | + | You can connect a PC directly to the iBTS with a cable to its LOCAL Ethernet port. |
| - | - **You have a DHCP server**: Start an ssh client (typically Putty on Windows) on port 22 and using the gateway’s IP address obtained from the DHCP server. \\ \\ | + | * In nominal case, after few seconds, your PC will obtain an IP address and you will be able to start a SSH client or HTTP connection on gateway IP 192.168.120.1. |
| - | - **You don't have a DHCP server**: Configure your PC Ethernet card to use 192.168.1.100 (netmask: 255.255.255.0) and start a ssh client (typically Putty on Windows) on port 22 and using the gateway default LOCAL IP address which is 192.168.1.1 ([[wiki:backhaul#local_ethernet|More information on the LOCAL Ethernet]]). | + | |
| - | * After getting prompt: Enter login/password (“''root''/''pdmk-**$serialno**''”). ''pdmk-**$serialno**'' is the default password on the gateway. See [[wiki:connection_credentials#default_password|here for more information]]. In case of failure, request password to Kerlink support team. | + | * In particular case you are using a DHCP server on your computer, gateway will directly obtain an IP address. A connection can then be done on this IP address. |
| + | |||
| + | See [[wiki:systeme_mana:connection_credentials#default_password|here for more information]] about SSH/HTTP connection details. | ||
| ===== Debug probe ===== | ===== Debug probe ===== | ||
| Line 126: | Line 127: | ||
| {{ :wiki:probe.jpg |}} | {{ :wiki:probe.jpg |}} | ||
| - | * After getting prompt, enter login/password (“''root'' / ''pdmk-**$serialno**''”). ''pdmk-**$serialno**'' is the default password on the gateway. See [[wiki:connection_credentials#default_password|here for more information]]. In case of failure, request password to Kerlink support team. | + | * After getting prompt, enter login/password (“''root'' / ''pdmk-**$serialno**''”). ''pdmk-**$serialno**'' is the default password on the gateway. See [[wiki::systeme_mana:connection_credentials#default_password|here for more information]]. In case of failure, request password to Kerlink support team. |
wiki/ibts/connect_ibts.1569418037.txt.gz · Last modified: 2019/09/25 15:27 by ghi
