wiki:lora:basic_station_forwarder
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:lora:basic_station_forwarder [2025/01/15 10:30] vsz |
wiki:lora:basic_station_forwarder [2025/09/08 14:35] (current) ehe [Actility LNS configuration tool] |
||
|---|---|---|---|
| Line 94: | Line 94: | ||
| </code> | </code> | ||
| ++++ | ++++ | ||
| + | ==== Kerlink CUPS configuration ==== | ||
| + | <note important>Only available since [[bspf_v3.3.0|Basic Station Packet Forwarder 3.3.0]]</note> | ||
| - | ==== Configuration ==== | + | After installation Kerlink Basic Station Packet Forwarder is disabled by default. |
| + | Once Basic Station Packet Forwarder started, if no configuration is available, it will connect to Kerlink CUPS using: | ||
| + | * cups-boot.uri | ||
| + | * cups-boot.key | ||
| + | * cups-boot.crt | ||
| + | |||
| + | Once connected to Kerlink CUPS, Basic Station Packet Forwarder will get its CUPS/LNS configuration. | ||
| + | |||
| + | It's now possible to set LNS configuration using Cockpit: [[https://cockpit.docs.kerlink.com/en/update-config/configure-lorawan|Configure LoRaWAN with Wanesy Management Cockpit]] | ||
| + | |||
| + | ==== Manual configuration ==== | ||
| Once installed, Kerlink Basic Station Packet Forwarder is disabled by default. It should first be configured for the wanted server (CUPS and/or LNS). | Once installed, Kerlink Basic Station Packet Forwarder is disabled by default. It should first be configured for the wanted server (CUPS and/or LNS). | ||
| - | As explained by [[https://lora-developers.semtech.com/build/software/lora-basics/lora-basics-for-gateways/?url=authmodes.html|Semtech documentation]], the procedure to connect to server may differ depending on authentication mode used by server. | + | As explained by [[https://doc.sm.tc/station/authmodes.html|Semtech documentation]], the procedure to connect to server may differ depending on authentication mode used by server. |
| === No authentication on LNS server === | === No authentication on LNS server === | ||
| Line 246: | Line 258: | ||
| </code> | </code> | ||
| Will configure basic station to forward messages provided by devices with DevAddr between 0x24000000 and 0x249fffff , or between 0x24b00000 and 0x25ffffff . | Will configure basic station to forward messages provided by devices with DevAddr between 0x24000000 and 0x249fffff , or between 0x24b00000 and 0x25ffffff . | ||
| + | |||
| + | ++++ | ||
| + | <note info> | ||
| + | The lead "0x" is not required before the base address of the filter. | ||
| + | </note> | ||
| + | |||
| + | ==== Local JoinEui Filtering ==== | ||
| + | |||
| + | In the case the LNS does not provide any JoinEui filter in the router_config message, it is possible to set local filters in order to only forward LoRa JoinRequest matching by a subset of EUIs. | ||
| + | |||
| + | To configure this feature, use the '-j' option of the klk_bs_config tool, and provide inclusive and/or exclusive filters to indicate the sets of JoinEuis to be kept and/or rejected. | ||
| + | |||
| + | ++++Example:| | ||
| + | |||
| + | <code bash> | ||
| + | klk_bs_config -e -j "848bcdfffe60b9df/48" | ||
| + | </code> | ||
| + | Will configure basic station to forward join requests using JoinEuis between 0x848bcdfffe600000 and 0x848bcdfffe60ffff . | ||
| ++++ | ++++ | ||
| Line 261: | Line 291: | ||
| * the API server URL | * the API server URL | ||
| * the chose frequency plan | * the chose frequency plan | ||
| - | |||
| - | <note warning>''klk_bs_config'' is still required after this to complete the Basic Station configuration.</note> | ||
| <note important> | <note important> | ||
| Line 276: | Line 304: | ||
| # Use TTN configuration tool for TTN LNS | # Use TTN configuration tool for TTN LNS | ||
| klk_ttn_config -u https://eu1.cloud.thethings.network -t NNSXS.R6D3ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHI.ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIABCDEFGHIJKLMNOPQ -f EU_863_870 | klk_ttn_config -u https://eu1.cloud.thethings.network -t NNSXS.R6D3ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHI.ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIABCDEFGHIJKLMNOPQ -f EU_863_870 | ||
| + | klk_bs_config -e | ||
| # Use TTN configuration tool for TTI LNS where tenant is your Tenant ID | # Use TTN configuration tool for TTI LNS where tenant is your Tenant ID | ||
| klk_ttn_config -u https://tenant.eu1.cloud.thethings.industries -t NNSXS.R6D3ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHI.ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIABCDEFGHIJKLMNOPQ -f EU_863_870 | klk_ttn_config -u https://tenant.eu1.cloud.thethings.industries -t NNSXS.R6D3ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHI.ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIABCDEFGHIJKLMNOPQ -f EU_863_870 | ||
| + | klk_bs_config -e | ||
| </code> | </code> | ||
| ++++ | ++++ | ||
| Line 327: | Line 357: | ||
| * US902-928 | * US902-928 | ||
| * Channel plans (1 to 8) comma separated (optional) | * Channel plans (1 to 8) comma separated (optional) | ||
| - | <note important> | ||
| - | ''klk_bs_config'' is still required after this to complete the Basic Station configuration. | ||
| - | </note> | ||
| ++++Example:| | ++++Example:| | ||
| Line 335: | Line 362: | ||
| # Use Loriot configuration tool in region US902 with 3 channel plans (US915_CH16_23, US915_CH40_47 and US915_CH56_63) | # Use Loriot configuration tool in region US902 with 3 channel plans (US915_CH16_23, US915_CH40_47 and US915_CH56_63) | ||
| klk_loriot_config -k ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJK-321abcdefgh -u https://eu1.loriot.io/1/nwk -n ABCD1234 -r US902-928 -p 3,6,8 | klk_loriot_config -k ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJK-321abcdefgh -u https://eu1.loriot.io/1/nwk -n ABCD1234 -r US902-928 -p 3,6,8 | ||
| + | klk_bs_config -e | ||
| </code> | </code> | ||
| ++++ | ++++ | ||
| Line 360: | Line 388: | ||
| * the LoRaWan region of the gateway | * the LoRaWan region of the gateway | ||
| * the Frequency Sub Band(s) to use (required for US915 and AU915) | * the Frequency Sub Band(s) to use (required for US915 and AU915) | ||
| - | <note important> | ||
| - | ''klk_bs_config'' is still required after this to complete the Basic Station configuration. | ||
| - | </note> | ||
| ++++Example:| | ++++Example:| | ||
| Line 368: | Line 393: | ||
| # Use AWS configuration tool | # Use AWS configuration tool | ||
| klk_aws_config -u some_user -k ABCDEFGHIJKLMNOPQRST-s ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMN-r eu-west-1 -l US915 -f 1 -b | klk_aws_config -u some_user -k ABCDEFGHIJKLMNOPQRST-s ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMN-r eu-west-1 -l US915 -f 1 -b | ||
| + | klk_bs_config -e | ||
| </code> | </code> | ||
| ++++ | ++++ | ||
| Line 446: | Line 472: | ||
| * the API server URL | * the API server URL | ||
| * the actility LoRaWAN region ID ( see https://oss-api.thingpark.com/tpe/7.3/Things-Management/network-manager/documentation-network-manager.html#/rf-regions ) | * the actility LoRaWAN region ID ( see https://oss-api.thingpark.com/tpe/7.3/Things-Management/network-manager/documentation-network-manager.html#/rf-regions ) | ||
| - | <note important> | ||
| - | ''klk_bs_config'' is still required after this to complete the Basic Station configuration. | ||
| - | </note> | ||
| ++++Example:| | ++++Example:| | ||
| Line 454: | Line 477: | ||
| # Use Actility configuration tool in region EU868 on 8 channels | # Use Actility configuration tool in region EU868 on 8 channels | ||
| klk_actility_config -i sub-123456789/test -s Abcdef1234567890Ghijklm987654321 -u https://community.thingpark.io -r EU868_8channels.448 | klk_actility_config -i sub-123456789/test -s Abcdef1234567890Ghijklm987654321 -u https://community.thingpark.io -r EU868_8channels.448 | ||
| + | klk_bs_config -e | ||
| </code> | </code> | ||
| ++++ | ++++ | ||
wiki/lora/basic_station_forwarder.1736933407.txt.gz · Last modified: 2025/01/15 10:30 by vsz
