This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:systeme_mana:features [2019/12/20 15:35] ghi |
wiki:systeme_mana:features [2025/09/09 10:39] (current) ehe [Manual Stock restore] |
||
|---|---|---|---|
| Line 77: | Line 77: | ||
| \\ | \\ | ||
| ==== Manual Stock restore ==== | ==== Manual Stock restore ==== | ||
| - | Since firmware >= 4.1, a "stock restore" can also be triggered manually without console access. \\ | ||
| - | To manually trigger a stock restore on a Wirnet gateway (excepting iFemtocell), please follow this procedure: | ||
| - | - Unpower the gateway by pushing ON/OFF button more than 5 seconds. | ||
| - | - Make sure [[wiki:systeme_mana:peripherals#leds|Power led]] is off and release button. | ||
| - | - Push On/OFF button to power-up the gateway and maintain until power and status leds blink alternatively. At this step, the gateway is ready to execute a stock restore operation. It will wait for a confirmation during 10 seconds. | ||
| - | - Release button and push it again to confirm the operation (leds will then stop blinking alternatively). | ||
| - | - Wait for the end of this operation (Leds behavior described [[wiki:systeme_mana:peripherals#leds|here]]). It takes approximately 2 minutes. | ||
| - | This procedure works for all Wirnet gateways excepting Wirnet iFemtocell which doesn't have an ON/OFF button. | + | Since firmware >= 4.1, a "stock restore" can also be triggered manually without console access. |
| ++++ | ++++ | ||
| - | To manually trigger a stock restore on Wirnet iFemtocell, please follow this procedure:| | + | To manually trigger a stock restore on Wirnet iBTS, Wirnet iStation, Wirnet iFemtocell, Wirnet iFemtoCell-evolution, please follow this procedure:| |
| - | - Push WPS button and maintain it. | + | - Turn off your gateway. |
| - | - Push Reset button one second. | + | - Press and hold the ON/OFF button (use the WPS button for iFemtoCell). |
| - | - At this step, the gateway is ready to execute a stock restore operation. It will wait for a confirmation during 10 seconds. | + | - Turn the power back on and wait a couple of seconds (the LEDs should blink fast). |
| - | - Release WPS button and push it again to confirm the operation (leds will then stop blinking alternatively). | + | - Release the button and click it once. |
| - Wait for the end of this operation (Leds behavior described [[wiki:systeme_mana:peripherals#leds|here]]). It takes approximately 2 minutes. | - Wait for the end of this operation (Leds behavior described [[wiki:systeme_mana:peripherals#leds|here]]). It takes approximately 2 minutes. | ||
| ++++ | ++++ | ||
| + | ++++ | ||
| + | To manually trigger a stock restore on Wirnet iZeptoCell, please follow this procedure:| | ||
| + | - Press the button once to trigger a software reset | ||
| + | - Push the button again when the status led is blinking red and maintain until power and status leds blink alternatively. At this step, the gateway is ready to execute a stock restore operation. It will wait for a confirmation during 10 seconds. | ||
| + | - Release button and push it again to confirm the operation (leds will then stop blinking alternatively). | ||
| + | - Wait for the end of this operation (Leds behavior described [[wiki:systeme_mana:peripherals#leds|here]]). It takes approximately 2 minutes. | ||
| + | ++++ | ||
| \\ | \\ | ||
| ===== Store & Restore configuration ===== | ===== Store & Restore configuration ===== | ||
| This functionality from firmware < 4.0 must not be used to store configuration files. In order to save configuration use the [[wiki:keros_custo:upgrade#configuration_management_sysupgrade|sysupgrade]] management. | This functionality from firmware < 4.0 must not be used to store configuration files. In order to save configuration use the [[wiki:keros_custo:upgrade#configuration_management_sysupgrade|sysupgrade]] management. | ||