wiki:systeme_mana:peripherals
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:systeme_mana:peripherals [2019/12/20 15:36] ghi |
wiki:systeme_mana:peripherals [2025/11/13 15:19] (current) ehe [Humidity and temperature sensor (Wirnet iStation only)] |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| GPS signal is handled by the kgpsd daemon. By default, this daemon sends the received nmea frames to both virtual ports ''/dev/nmea1'' and ''/dev/nmea2''. Once a program reads a line from a virtual port, this line is deleted. Thus, only one program should read a virtual port at a time. | GPS signal is handled by the kgpsd daemon. By default, this daemon sends the received nmea frames to both virtual ports ''/dev/nmea1'' and ''/dev/nmea2''. Once a program reads a line from a virtual port, this line is deleted. Thus, only one program should read a virtual port at a time. | ||
| - | Some Wirnet™ Productline gateways don't have a GPS device. For these gateways, kgpsd will not be launched and ''/dev/nmeaX'' files will not be created. | + | Some Wirnet™ i-series gateways don't have a GPS device. For these gateways, kgpsd will not be launched and ''/dev/nmeaX'' files will not be created. |
| By default, the packet forwarder reads the ''/dev/nmea1'' virtual port. | By default, the packet forwarder reads the ''/dev/nmea1'' virtual port. | ||
| Line 79: | Line 79: | ||
| ==== Temperature ==== | ==== Temperature ==== | ||
| + | |||
| + | <note>Note that [[https://en.wikipedia.org/wiki/Lm_sensors|lmsensors]] library can also be used to extract temperature from Firmware 4.2 and above</note> | ||
| === CPU temperature sensor === | === CPU temperature sensor === | ||
| Line 84: | Line 86: | ||
| All Wirnet™ Gateways have a temperature sensor in their CPU. To read the sensor output: | All Wirnet™ Gateways have a temperature sensor in their CPU. To read the sensor output: | ||
| <code bash> | <code bash> | ||
| - | cat /sys/class/hwmon/hwmon0/temp1_input | + | cat /sys/class/thermal/thermal_zone0/temp |
| </code> | </code> | ||
| Line 117: | Line 119: | ||
| Humidity level is: | Humidity level is: | ||
| - | * in_humidityrelative_raw * in_humidityrelative_scale in % | + | * in_humidityrelative_raw * in_humidityrelative_scale / 1000 in % |
| To temperature: | To temperature: | ||
| Line 158: | Line 160: | ||
| On Wirnet iStation: | On Wirnet iStation: | ||
| - | * power LED is the green LED under the power button | + | * power LED is the green LED (left) under the power button |
| - | * status LED is the red LED under the power button | + | * status LED is the red LED (right) under the power button |
| + | |||
| + | On Wirnet iZeptoCell: | ||
| + | *power and status led are one bi-color LED | ||
| + | *this LED is represent with the power symbol | ||
| ==== Other LEDs ==== | ==== Other LEDs ==== | ||
| Line 200: | Line 206: | ||
| ++++ | ++++ | ||
| + | ++++ | ||
| + | Wirnet iZeptoCell | | ||
| + | |||
| + | There are 3 LEDs on the Wirnet iZeptoCell: | ||
| + | * LED 1 : Power/Status (represent with the power symbol) | ||
| + | * LED 2 : Backhaul (represent with the screen symbol) | ||
| + | * LED 3 : LoRa Traffic (represent with the radio wave symbol) | ||
| + | |||
| + | ^ Status ^ Backhaul LED ^ | ||
| + | | **WMC - Not connected (2)** | <fc #ff0000>Red</fc> | | ||
| + | | **WMC - During connection (2)** | <fc #008000>Green blinking </fc> | | ||
| + | | **WMC - Connected (2)** | <fc #008000>Green </fc> | | ||
| + | |||
| + | ^ Status ^ LoRa traffic ^ | ||
| + | | **Boot** | <fc #ff0000>Red</fc> | | ||
| + | | **Packet forwarder - Rx (1)** | <fc #008000>Green blinking </fc> | | ||
| + | | **Packet forwarder - Tx (1)** | <fc #ff0000>Red blinking </fc> | | ||
| + | |||
| + | (1): This LEDs behavior is only available in the packet forwarder provided on this wiki. | ||
| + | (2): This LEDs behavior is only available when Wanesy Management Center is used. | ||
| + | |||
| + | ++++ | ||
| + | |||
| + | ==== LEDs management ==== | ||
| + | |||
| + | It is possible to manage LEDs in some scripts, to make it blinking for example.\\ | ||
| + | Here some scripts examples with LED path and management: | ||
| + | * In [[wiki:keros_custo:sw_updates#specific_files | usb.autorun specific file]]. | ||
| + | * In [[wiki:keros_custo:scripts | Initialization scripts]] wiki page. | ||
wiki/systeme_mana/peripherals.1576852616.txt.gz · Last modified: 2019/12/20 15:36 by ghi
