Wirnet™ i-series

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== IPsec / OpenVPN ======

This section does not concern WMC server. The Kerlink WMC already provides OpenVPN.

The KerOS firmware comes with strongSwan and OpenVPN clients pre-installed. The credentials, however, need to be stored in a very specific way, described in this page.

<note warning>Please ensure the server's version matches the client's version.

For example, if the embedded client's version is OpenVPN 2.3.14, please ensure the server uses a compatible version (if possible, the same).

You can check the version with:
<code bash>openvpn --version</code>

Or:
<code bash>ipsec --version</code></note>


===== KerOs 4.x =====

==== Overview ====

The steps to make the VPN work are the following:

  - Setup a PKI (Public Key Infrastructure) to be able to produce secrets.
  - Generate secrets for the gateways to connect, in the PKCS#12 format.
  - Write the main VPN configuration file (must match the server configuration).
  - Write the ProvenCore specific configuration file.
  - Cipher the ProvenCore specific configuration file.
  - Cipher the P12 file.
  - Initialize the TrustZone.
  - Upload the ProvenCore specific ciphered configuration file to the TrustZone.
  - Upload the ciphered P12 file to the TrustZone.
  - Start the VPN client using the main VPN configuration file.

<note tip>All the ''pnr_uploader'' commands return with a status. If the status is different from ''0'', this is a failure. Stop and ensure you followed all the steps before you continue.</note>

==== General information ====


Wirnet™ i-series gateways embed the TrustZone security feature provided by ARM microprocessors.
TrustZone technology is used to run a trusted boot and a trusted OS to create a Trusted Execution Environment.

The trusted OS is ProvenCore, from Prove&Run.

The firmware comes with two VPN clients: strongSwan (IPSec) and OpenVPN. These clients are modified to be able to read the secrets (passwords, keys, certificates, etc.) from that hardware-backed secure storage. This means that the sensitive data is encrypted and stored in a memory that cannot be read from the userland or even the kernel. The only way the data can be extracted is through the use of the embedded VPN clients, which are compiled using a dedicated library provided by //ProvenCore//.


The entire secret management on KerOS firmware is handled by //ProvenCore// for OpenVPN/strongSwan.

<note info>
The //TrustZone// in the Wirnet iBTS is composed of five blocks, each having its dedicated purpose:

  * Block 0: ''ipsec.secrets'' config file
  * Block 2: OpenVPN config file
  * Block 10: Client certificate (OpenVPN)
  * Block 20: Client certificate (IPsec)
</note>

==== Step by step guide ====


Here are some examples that can be used to setup a whole VPN infrastructure:

  - [[wiki:network_mana:secure_network:keros_4.x:vpn_pki_management|VPN - PKI management]]: VPN server setup
  - [[wiki:network_mana:secure_network:keros_4.x:vpn_server_configuration|VPN server configuration]]: VPN server configuration
  - [[wiki:network_mana:secure_network:keros_4.x:setting_up_the_vpn_client|Setting up the VPN client]]: VPN client configuration
  - [[wiki:network_mana:secure_network:keros_4.x:running_the_application|Running the application]]: VPN client startup



===== KerOs 5.x =====

==== IPsec ====

IPSec is not yet supported 


==== OpenVPN ====
On keros 5.x, unlike keros 4.x, OpenVPN is independant from ProvenCore and can be used like as on any linux system.

There may be some limitations at the level of the Cipher depending on the version used. Use the command below to know the supported cipher : 
<code bash>openvpn --show-ciphers</code>

Step by step guide : [[wiki:network_mana:secure_network:keros_5.x:openvpn]]
Wirnet™ i-series

User Tools

Site Tools

Page Tools
