#################################################
#                                               #
# Client-side OpenVPN 2.X config file for       #
# connecting to multi-client server.            #
#                                               #
# Comments are preceded with '#' or ';'         #
#                                               #
#################################################

# Specify that we are a client and that we
# will be pulling certain config file directives
# from the server.
client

# Use the same setting as you are using on
# the server.
# On most systems, the VPN will not function
# unless you partially or fully disable
# the firewall for the TUN/TAP interface.
;dev tap
dev tun


# Are we connecting to a TCP or
# UDP server?  Use the same setting as
# on the server.
;proto tcp
proto udp

# The hostname/IP and port of the server.
# You can have multiple remote entries
# to load balance between the servers.
remote OPENVPN_SERVER_IP OPENVPN_SERVER_PORT

# Choose a random host from the remote
# list for load-balancing.  Otherwise
# try hosts in the order specified.
;remote-random

# Keep trying indefinitely to resolve the
# host name of the OpenVPN server.  Very useful
# on machines which are not permanently connected
# to the internet such as laptops.
resolv-retry infinite

# Most clients don't need to bind to
# a specific local port number.
nobind

# Downgrade privileges after initialization (non-Windows only)
user nobody
group nogroup

# Try to preserve some state across restarts.
persist-key
persist-tun
persist-local-ip
persist-remote-ip

# If you are connecting through an
# HTTP proxy to reach the actual OpenVPN
# server, put the proxy server/IP and
# port number here.  See the man page
# if your proxy server requires
# authentication.
;http-proxy-retry # retry on connection failures
;http-proxy [proxy server] [proxy port #]

# Announce to TCP sessions running over the
# tunnel that they should limit their send packet
#sizes such that after OpenVPN has encapsulated them,
# the resulting UDP packet size that OpenVPN sends
# to its peer will not exceed max bytes.
mssfix 1200

# Wireless networks often produce a lot
# of duplicate packets.  Set this flag
# to silence duplicate packet warnings.
;mute-replay-warnings

# SSL/TLS parms.
# See the server config file for more
# description.  It's best to use
# a separate .crt/.key file pair
# for each client.  A single ca
# file can be used for all clients.
pkcs12 [[INLINE]]

# Verify server certificate by checking that the
# certicate has the correct key usage set.
# This is an important precaution to protect against
# a potential attack discussed here:
#  http://openvpn.net/howto.html#mitm
#
# To use this feature, you will need to generate
# your server certificates with the keyUsage set to
#   digitalSignature, keyEncipherment
# and the extendedKeyUsage to
#   serverAuth
# EasyRSA can do this for you.
remote-cert-tls server

# If a tls-auth key is used on the server
# then every client must also have the key.
;tls-auth ta.key 1

# Select a cryptographic cipher.
# This config item must be copied to
# the client config file as well.
;cipher BF-CBC        # Blowfish (default)
;cipher AES-128-CBC   # AES
;cipher DES-EDE3-CBC  # Triple-DES
cipher AES-256-CBC

# Enable compression on the VPN link.
# Don't enable this unless it is also
# enabled in the server config file.
comp-lzo

# Set log file verbosity.
verb 3

# Silence repeating messages
;mute 20

# The keepalive directive causes ping-like
# messages to be sent back and forth over
# the link so that each side knows when
# the other side has gone down.
# Ping every 10 seconds, assume that remote
# peer is down if no ping received during
# a 120 second time period.
keepalive 60 600

# 0 -- Strictly no calling of external programs.
# 1 -- (Default) Only call built-in executables such as  ifconfig,
# ip, route, or netsh.
# 2  --  Allow  calling  of  built-in executables and user-defined
# scripts.
# 3 -- Allow passwords to be passed to scripts  via  environmental
# variables (potentially unsafe).
script-security 2

# up   Executed after TCP/UDP socket bind and TUN/TAP open.
# down Executed after TCP/UDP and TUN/TAP close.
;up /etc/openvpn/update-resolv-conf
;down /etc/openvpn/update-resolv-conf