Wirnet™ i-series

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

====== Setup of Wirnet™ iZeptoCell Cellular Gateway ======

===== Documentation =====

  * Leaflet (contains the list of accessories): {{ :documentation:commercial_leaflet_wirnet_izeptocell_cellular_v2.7.pdf|}}\\
  * Quick start guide: {{ :documentation:e-dmk_-_quick_start_-_izepto_cellular_-_v1.0.pdf |}}
  * Wanesy® Cellular Connectivity leaflet: {{ :documentation:wanesy-cellular_connectivity_commercial_leaflet_v1.0.pdf |}}

===== Zero Touch provisioning (ZTP) feature =====

The KerOS firmware integrates the Zero Touch provisioning (ZTP) feature. When you receive the gateway, you don’t need anymore to install software or to configure it, it is plug&play.

Supported configuration includes:
  * Connection to Kerlink Wanesy Management Center (WMC).
  * Chirpstack or TTN configuration.

ZTP feature is available when the gateway boots for the first time with an available internet connection.

<note warning>The gateway must remain powered up and connected to Internet during the entire ZTP process.</note>

To enable ZTP on a gateway, it must be pre-declared on Kerlink ZTP Management server. 
Please contact Kerlink for more information at [[support@kerlink.fr]].


===== Connection to the gateway =====

You can connect a PC directly to the Wirnet iZeptoCell **with a USB cable.** In this mode, the gateway will simulate an ethernet device. \\
In nominal case, after few seconds, your PC will obtain an IP address and you will be able to start a SSH client or HTTP connection on gateway IP 192.168.120.1. \\
In particular case you are using a DHCP server on your computer, gateway will directly obtain an IP address. A connection can then be done on this IP address.\\
See [[wiki:systeme_mana:connection_credentials#default_password|here for more information]] about SSH/HTTP connection details.

Once connected through USB cable, connection to the gateway can either be done via:

  * SSH:  [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:connection_credentials#network_shell_access_ssh|click here]]. 
  * Web Interface:  [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:webui:zcel#Web Interface|click here]].

===== Factory reset =====
If needed the factory reset of the gateway is feasible. Consult the stock restore process:  [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:features#stock_restore|click here]]

===== Get the logs =====
To simplify the log gathering process, Kerlink developed automatic log gathering methods. Consult the Automatic log gathering chapter:  [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:support:troubleshoot#automatic_log_gathering|click here]]
===== Connect an iZeptoCell to WMC =====

  * Please contact Kerlink Support team at [[support@kerlink.fr]] to get a Magic Link to update the gateway with the relevant firmware and embedded applications.
  * [[https://wikikerlink.fr/wanesy-ran/doku.php?id=wiki:wiki3:quickstart|How to connect a gateway to WMC?]]





===== LoRaWAN protocol =====
Kerlink is a member of LoRa Alliance and the Kerlink gateway is compatible with LoRaWAN protocol.
If you need information about LoRaWAN network protocol please contact the LoRa Alliance and request LoRaWAN specification : [[https://lora-alliance.org/lorawan-for-developers]]

===== Register to wiki update notifications =====
You can register for Wiki update notifications by clicking on the envelope icon (“Manage subscriptions”) on the right side of the page.
Wirnet™ i-series

User Tools

Site Tools

Page Tools
