This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wiki:introduction:quickstart [2020/03/13 16:05] ghi [Web user interface access] |
wiki:introduction:quickstart [2024/04/29 10:50] (current) ehe [Magic Link] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Quick start ====== | + | {{ :images:spnbanner.png?nolink&300 |}} |
+ | ====== Quick start Wanesy™ SPN====== | ||
+ | |||
+ | ===== What's new? ===== | ||
+ | |||
+ | For [[wiki:firmware:installation#with_web_interface_recommended|compatible iSeries ONLY]]: You can now download and install the **SPN firmware & Slave license** or **SPN firmware & Master license** using a single Magic Link. \\ | ||
+ | See [[wiki:introduction:quickstart#magic_link|Magic Link]]. | ||
+ | |||
+ | ===== Introduction ===== | ||
+ | |||
+ | Check your license version | ||
+ | |||
+ | |||
+ | |||
+ | | **License** | @lightgreen:Version | @lightgreen:Product | | ||
+ | | **SRVLIC-SPN00** | @lightgreen:SPN V1 | @lightgreen:Wirnet Station | | ||
+ | | **SRVLIC-SPN01** | @lightgreen:SPN V1 | @lightgreen:Wirnet iFemtoCell | | ||
+ | | **SRVLIC-SPN2x** | @lightgreen:SPN V2 | @lightgreen:Wirnet iFemtoCell / iStation / iFemtoCell-Evolution | | ||
+ | |||
+ | |||
+ | |||
+ | If you have SRVLIC-SPN01 SPN V1 for **Wirnet iFemtoCell** gateway you must use the following Wiki: [[https://wikikerlink.fr/wirnet-ifemtocell-spn/doku.php?id=home|Wirnet iFemtocell SPN]]. | ||
+ | |||
+ | |||
+ | |||
+ | If you have SRVLIC-SPN00 SPN V1 for **Wirnet Station** gateway you must use the following Wiki: [[https://wikikerlink.fr/lora-iot-station-spn/doku.php?id=lorahome|IoT Station SPN]]. | ||
+ | |||
+ | ===== Documentation ===== | ||
+ | |||
+ | |||
+ | * Leaflet : {{ :media:Commercial_leaflet_Wanesy_SPN_V2.5.pdf |}}\\ | ||
- | This section aims to guide a user through the main steps of the configuration of the Wanesy SPN firmware in order to receive data from an end-device. | ||
- | Prerequisites: | ||
- | * Wanesy SPN installed on a gateway. | ||
- | * Wanesy SPN license file available for the gateway. | ||
- | * Google Chrome browser is used to connect to web user interface. | ||
- | To use an end-device with Wanesy SPN, the end-device and the gateway need to use the same LoRa configuration. | ||
- | Some parameters are common to the entire fleet and some parameters are end-device specific. | ||
===== Connection to the gateway ===== | ===== Connection to the gateway ===== | ||
Line 27: | Line 51: | ||
Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal. | Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal. | ||
- | ===== Web user interface access ===== | + | ==== Web user interface access ==== |
The home web interface is accessible at the following address: | The home web interface is accessible at the following address: | ||
^ Gateway model ^ Address ^ | ^ Gateway model ^ Address ^ | ||
- | | **Wirnet iFemtoCell** | ''http://klk-wifc-XXXXXX/'' | | + | | **Wirnet™ iFemtoCell** | ''http://klk-wifc-XXXXXX/'' | |
- | | **Wirnet iStation** | ''http://klk-wiis-XXXXXX/'' | | + | | **Wirnet™ iStation** | ''http://klk-wiis-XXXXXX/'' | |
- | | **Wirnet iFemtoCell-evolution** | ''http://klk-fevo-XXXXXX/'' | | + | | **Wirnet™ iFemtoCell-Evolution** | ''http://klk-fevo-XXXXXX/'' | |
Where ''XXXXXX'' are the last 6 digits of board id. | Where ''XXXXXX'' are the last 6 digits of board id. | ||
Line 39: | Line 63: | ||
Address to be used with the gateway owning the following label: ''http://klk-wifc-03002e/'' (case insensitive) | Address to be used with the gateway owning the following label: ''http://klk-wifc-03002e/'' (case insensitive) | ||
- | {{.:..:..:images:ifemtocell_label.jpg?400|Board ID can be retrieved on gateway case}} | + | {{:wiki:images:ifemtocell_label.jpg?400|Board ID can be retrieved on gateway case}} |
Once login screen displayed enter following login/password:\\ | Once login screen displayed enter following login/password:\\ | ||
Line 45: | Line 69: | ||
password: ''spnpwd'' | password: ''spnpwd'' | ||
- | ===== License installation ===== | + | ==== Network shell access (SSH) ==== |
+ | |||
+ | Start an SSH client (typically Putty on Windows) using the gateway’s name or IP address (the port is the standard 22). | ||
+ | Default password is built using the last 6 digits of the serial number board ID: pdmk-$serialno. | ||
+ | |||
+ | After getting a prompt: enter login/password (e.g. “''root'' / ''pdmk-**$serialno**''”). | ||
+ | |||
+ | ===== Firmware Installation ===== | ||
+ | |||
+ | * Wanesy SPN firmware installation: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:installation|click here]] | ||
+ | * Wanesy SPN firmware upgrade: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:upgrade|click here]] | ||
+ | * Wanesy SPN firmware uninstall: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:uninstall|click here]] | ||
+ | |||
+ | ===== SPN Configuration ===== | ||
+ | |||
+ | ==== Magic Link ==== | ||
+ | <note important>**Prerequisite:** Your gateway should run in **SPN firmare 2.X** or **KerOS firmware version 4.3.3 or superior**. | ||
+ | </note> | ||
+ | |||
+ | To control the version: | ||
+ | * ''opkg list-installed'': lists the installed packages. | ||
+ | |||
+ | |||
+ | **Magic Link for SLAVE configuration**:\\ | ||
+ | ''curl --compressed -s https://upgrade.wanesy.com/SPN | sh'' | ||
+ | |||
+ | |||
+ | **Magic Link for MASTER configuration**:\\ | ||
+ | ''curl --compressed -s https://upgrade.wanesy.com/SPN-master | sh''\\ | ||
+ | \\ | ||
+ | |||
+ | |||
+ | ==== License installation ==== | ||
To have all the features of Wanesy SPN firmware, a license file is needed. | To have all the features of Wanesy SPN firmware, a license file is needed. | ||
Line 52: | Line 108: | ||
* Drag and drop license file or click on the panel to upload the license file | * Drag and drop license file or click on the panel to upload the license file | ||
- | ===== Password update ===== | + | ==== Password update ==== |
For security reasons, Kerlink strongly advises its customers to change the default password. | For security reasons, Kerlink strongly advises its customers to change the default password. | ||
Line 59: | Line 116: | ||
* Update password | * Update password | ||
- | ===== Region configuration ===== | + | ==== Region configuration ==== |
The region where the gateway will be used needs to be configured. | The region where the gateway will be used needs to be configured. | ||
Line 66: | Line 123: | ||
* Validate the modification with the ''Save configuration'' button | * Validate the modification with the ''Save configuration'' button | ||
- | ===== Rx configuration ===== | + | ==== Rx configuration ==== |
Gateway hardware contains 2 RF radios (0.8 MHz bandwidth for each radio). 8 multi SF channels and 1 mono SF channel can be configured on these 2 radios. | Gateway hardware contains 2 RF radios (0.8 MHz bandwidth for each radio). 8 multi SF channels and 1 mono SF channel can be configured on these 2 radios. | ||
Line 79: | Line 136: | ||
* Validate the modification with the ''Save configuration'' button | * Validate the modification with the ''Save configuration'' button | ||
- | ===== End-device registration and activation ===== | + | ==== End-device registration and activation ==== |
End-device must be registered before receiving any data | End-device must be registered before receiving any data | ||
Line 87: | Line 144: | ||
* Validate the end-device with the ''Add end-device'' button | * Validate the end-device with the ''Add end-device'' button | ||
- | ===== Received data ==== | + | ==== Received data === |
* Go to ''Fleet => Received data'' to display Rx data sent by the registered end-device. Click on ''Refresh'' button if needed (bottom right corner of the page) | * Go to ''Fleet => Received data'' to display Rx data sent by the registered end-device. Click on ''Refresh'' button if needed (bottom right corner of the page) | ||
+ | |||
+ | ===== Register to wiki update ===== | ||
+ | |||
+ | You can now register to Wiki update notifications: | ||
+ | - **Click** on the envelope icon (//Manage subscriptions//) on the right side of the page. | ||
+ | - **Choose** your option and Subscribe. | ||
+ | - **Check** your subscription by click again on the envelope icon. | ||
+ | |||
+ | {{:images:wiki_subscribe.png?nolink |}} |