wiki:introduction:quickstart
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:introduction:quickstart [2020/04/29 11:20] mbi [Web user interface access] |
wiki:introduction:quickstart [2024/04/29 10:50] (current) ehe [Magic Link] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Quick start ====== | + | {{ :images:spnbanner.png?nolink&300 |}} |
| + | ====== Quick start Wanesy™ SPN====== | ||
| + | |||
| + | ===== What's new? ===== | ||
| + | |||
| + | For [[wiki:firmware:installation#with_web_interface_recommended|compatible iSeries ONLY]]: You can now download and install the **SPN firmware & Slave license** or **SPN firmware & Master license** using a single Magic Link. \\ | ||
| + | See [[wiki:introduction:quickstart#magic_link|Magic Link]]. | ||
| + | |||
| + | ===== Introduction ===== | ||
| + | |||
| + | Check your license version | ||
| + | |||
| + | |||
| + | |||
| + | | **License** | @lightgreen:Version | @lightgreen:Product | | ||
| + | | **SRVLIC-SPN00** | @lightgreen:SPN V1 | @lightgreen:Wirnet Station | | ||
| + | | **SRVLIC-SPN01** | @lightgreen:SPN V1 | @lightgreen:Wirnet iFemtoCell | | ||
| + | | **SRVLIC-SPN2x** | @lightgreen:SPN V2 | @lightgreen:Wirnet iFemtoCell / iStation / iFemtoCell-Evolution | | ||
| + | |||
| + | |||
| + | |||
| + | If you have SRVLIC-SPN01 SPN V1 for **Wirnet iFemtoCell** gateway you must use the following Wiki: [[https://wikikerlink.fr/wirnet-ifemtocell-spn/doku.php?id=home|Wirnet iFemtocell SPN]]. | ||
| + | |||
| + | |||
| + | |||
| + | If you have SRVLIC-SPN00 SPN V1 for **Wirnet Station** gateway you must use the following Wiki: [[https://wikikerlink.fr/lora-iot-station-spn/doku.php?id=lorahome|IoT Station SPN]]. | ||
| + | |||
| + | ===== Documentation ===== | ||
| + | |||
| + | |||
| + | * Leaflet : {{ :media:Commercial_leaflet_Wanesy_SPN_V2.5.pdf |}}\\ | ||
| - | This section aims to guide a user through the main steps of the configuration of the Wanesy SPN firmware in order to receive data from an end-device. | ||
| - | Prerequisites: | ||
| - | * Wanesy SPN installed on a gateway. | ||
| - | * Wanesy SPN license file available for the gateway. | ||
| - | * Google Chrome browser is used to connect to web user interface. | ||
| - | To use an end-device with Wanesy SPN, the end-device and the gateway need to use the same LoRa configuration. | ||
| - | Some parameters are common to the entire fleet and some parameters are end-device specific. | ||
| ===== Connection to the gateway ===== | ===== Connection to the gateway ===== | ||
| Line 27: | Line 51: | ||
| Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal. | Your computer may take some time to get the “connected” status, and the interface will have a “limited connectivity”, which is normal. | ||
| - | ===== Web user interface access ===== | + | ==== Web user interface access ==== |
| The home web interface is accessible at the following address: | The home web interface is accessible at the following address: | ||
| ^ Gateway model ^ Address ^ | ^ Gateway model ^ Address ^ | ||
| - | | **Wirnet iFemtoCell** | ''http://klk-wifc-XXXXXX/'' | | + | | **Wirnet™ iFemtoCell** | ''http://klk-wifc-XXXXXX/'' | |
| - | | **Wirnet iStation** | ''http://klk-wiis-XXXXXX/'' | | + | | **Wirnet™ iStation** | ''http://klk-wiis-XXXXXX/'' | |
| - | | **Wirnet iFemtoCell-evolution** | ''http://klk-fevo-XXXXXX/'' | | + | | **Wirnet™ iFemtoCell-Evolution** | ''http://klk-fevo-XXXXXX/'' | |
| Where ''XXXXXX'' are the last 6 digits of board id. | Where ''XXXXXX'' are the last 6 digits of board id. | ||
| Line 42: | Line 66: | ||
| Once login screen displayed enter following login/password:\\ | Once login screen displayed enter following login/password:\\ | ||
| - | user: ''**spn**''\\ | + | user: ''spn''\\ |
| - | password: ''**spnpwd**'' | + | password: ''spnpwd'' |
| - | ===== License installation ===== | + | ==== Network shell access (SSH) ==== |
| + | |||
| + | Start an SSH client (typically Putty on Windows) using the gateway’s name or IP address (the port is the standard 22). | ||
| + | Default password is built using the last 6 digits of the serial number board ID: pdmk-$serialno. | ||
| + | |||
| + | After getting a prompt: enter login/password (e.g. “''root'' / ''pdmk-**$serialno**''”). | ||
| + | |||
| + | ===== Firmware Installation ===== | ||
| + | |||
| + | * Wanesy SPN firmware installation: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:installation|click here]] | ||
| + | * Wanesy SPN firmware upgrade: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:upgrade|click here]] | ||
| + | * Wanesy SPN firmware uninstall: [[https://wikikerlink.fr/wanesy-spn/doku.php?id=wiki:firmware:uninstall|click here]] | ||
| + | |||
| + | ===== SPN Configuration ===== | ||
| + | |||
| + | ==== Magic Link ==== | ||
| + | <note important>**Prerequisite:** Your gateway should run in **SPN firmare 2.X** or **KerOS firmware version 4.3.3 or superior**. | ||
| + | </note> | ||
| + | |||
| + | To control the version: | ||
| + | * ''opkg list-installed'': lists the installed packages. | ||
| + | |||
| + | |||
| + | **Magic Link for SLAVE configuration**:\\ | ||
| + | ''curl --compressed -s https://upgrade.wanesy.com/SPN | sh'' | ||
| + | |||
| + | |||
| + | **Magic Link for MASTER configuration**:\\ | ||
| + | ''curl --compressed -s https://upgrade.wanesy.com/SPN-master | sh''\\ | ||
| + | \\ | ||
| + | |||
| + | |||
| + | ==== License installation ==== | ||
| To have all the features of Wanesy SPN firmware, a license file is needed. | To have all the features of Wanesy SPN firmware, a license file is needed. | ||
| Line 51: | Line 107: | ||
| * Go to ''Administration => License'' menu | * Go to ''Administration => License'' menu | ||
| * Drag and drop license file or click on the panel to upload the license file | * Drag and drop license file or click on the panel to upload the license file | ||
| - | * Reboot | + | |
| - | ===== Password update ===== | + | ==== Password update ==== |
| For security reasons, Kerlink strongly advises its customers to change the default password. | For security reasons, Kerlink strongly advises its customers to change the default password. | ||
| Line 59: | Line 116: | ||
| * Update password | * Update password | ||
| - | ===== Region configuration ===== | + | ==== Region configuration ==== |
| The region where the gateway will be used needs to be configured. | The region where the gateway will be used needs to be configured. | ||
| Line 66: | Line 123: | ||
| * Validate the modification with the ''Save configuration'' button | * Validate the modification with the ''Save configuration'' button | ||
| - | ===== Rx configuration ===== | + | ==== Rx configuration ==== |
| Gateway hardware contains 2 RF radios (0.8 MHz bandwidth for each radio). 8 multi SF channels and 1 mono SF channel can be configured on these 2 radios. | Gateway hardware contains 2 RF radios (0.8 MHz bandwidth for each radio). 8 multi SF channels and 1 mono SF channel can be configured on these 2 radios. | ||
| Line 79: | Line 136: | ||
| * Validate the modification with the ''Save configuration'' button | * Validate the modification with the ''Save configuration'' button | ||
| - | ===== End-device registration and activation ===== | + | ==== End-device registration and activation ==== |
| End-device must be registered before receiving any data | End-device must be registered before receiving any data | ||
| Line 87: | Line 144: | ||
| * Validate the end-device with the ''Add end-device'' button | * Validate the end-device with the ''Add end-device'' button | ||
| - | ===== Received data ==== | + | ==== Received data === |
| * Go to ''Fleet => Received data'' to display Rx data sent by the registered end-device. Click on ''Refresh'' button if needed (bottom right corner of the page) | * Go to ''Fleet => Received data'' to display Rx data sent by the registered end-device. Click on ''Refresh'' button if needed (bottom right corner of the page) | ||
| + | |||
| + | ===== Register to wiki update ===== | ||
| + | |||
| + | You can now register to Wiki update notifications: | ||
| + | - **Click** on the envelope icon (//Manage subscriptions//) on the right side of the page. | ||
| + | - **Choose** your option and Subscribe. | ||
| + | - **Check** your subscription by click again on the envelope icon. | ||
| + | |||
| + | {{:images:wiki_subscribe.png?nolink |}} | ||
wiki/introduction/quickstart.1588152046.txt.gz · Last modified: 2020/04/29 11:20 by mbi
Page Tools
