Wanesy Wave firmware v2.2.0 (July 2022)

Wanesy Wave firmware v2.2.0 (July 2022)

Changes from previous version

New features

WiFi Sniffer Mode

Restrictions

If the installed firmware is 1.8.0 or lower, firmware upgrade procedure must respect specific order described in section below.

Firmware

Compatibility

Hardware

This release is compatible with the following Wanesy Wave revisions:

Wanest Wave 868:
- Fully compatible with Wanesy Wave Board ID xxxDAcxxxxxx, xxxDAdxxxxxx, xxxDAexxxxxx.
Wanesy Wave 915:
- Fully compatible with Wanesy Wave Board ID xxxDBcxxxxxx, xxxDBdxxxxxx, xxxDBexxxxxx, xxxDBfxxxxxx .

Software

STM32 MCU firmware Ver. 2.2.0
ESP32 MCU firmware Ver. 2.2.0

Delivery

The firmware is released in two files: STM32 MCU firmware binary 'kbin' file and ESP32 MCU firmware binary file.

STM32 MCU :
To update the firmware, follow instruction on the Firmware update section of the Setup page: click here.

ESP32 MCU:
To update the firmware, follow instruction on the Firmware update section of the Setup page: click here.

Download

Wi-Fi: Firmware update

Please check your firmware version before updating and follow the instructions in the corresponding section

Installed firmware is v1.9.0 or higher version

Regular firmware update can be followed (update ESP32 first), please read e-con-wanesy_wave_fw_update_wifi_v1.2.pdf available in the Wanesy™ Wave Setup: Documentation section.

Installed firmware is v1.8.0 or lower version

If the installed firmware is v1.8.0 or lower version, the firmware update procedure must respect the specific order described below (update STM32 first):

steps	STM32 version	ESP32 version	SSID	Actions
#1	v1.7.0/v1.8.0	v1.7.0/v1.8.0	optout_klk/wave_xxxx	Place product upright away from wall or table
				Upload STM32 v2.0.1 image
				Wait until green LED is back ON (ie. no longer blinking)
#2	v2.0.1	v1.7.0/v1.8.0	optout_klk/wave_xxxx	Verify STM32 version in device_info.txt file
#2	v2.0.1	v1.7.0/v1.8.0	optout_klk/wave_xxxx	Upload ESP32 v2.0.1 image
#3	v2.0.1	v2.0.1	wave_xxxx	Verify ESP32 version in esp32_version.txt file (displayed version is 2.0.0)

Wanesy Wave 868: wifiupdate_wanesywave_eu868_v2.2.0_20220707_revs_cde.zip
- STM32 file: stm32_wanesywave_EU868_v2.2.0_DAcde.kbin (md5: 39f7e4136948d2380473e6092e020ef4).
- ESP32 file: esp32_firmware_v2.2.0.bin (md5: 661949ff2cf24e5b93b2b92e54dce98e).

Wanesy Wave 915: wifiupdate_wanesywave_us915_v2.2.0_20220707_revs_cdef.zip
- STM32 file: stm32_wanesywave_US915_v2.2.0_DBcdef.kbin (md5: b95353709a8bc3a354f09d210a1bba43).
- ESP32 file: esp32_firmware_v2.2.0.bin (md5: 661949ff2cf24e5b93b2b92e54dce98e).

Wi-Fi: region configuration

Wanesy Wave 868: region_conf_wifiupdate_wanesywave_868_v1.8.0_20210421_revs_cde.zip
- cmd_region_EU868.txt
- cmd_region_IN865.txt

Wanesy Wave 915: region_conf_wifiupdate_wanesywave_915_v1.8.0_20210421_revs_cdef.zip
- cmd_region_US915.txt
- cmd_region_AU915.txt
- cmd_region_AS923.txt

History

2.2.0 (June 2022):
- WiFi Sniffer Mode
2.1.0 (March 2022):
- Dwell Time Applicative Configuration
2.0.1 (October 2021):
- BLE Asset Monitoring
- LoRaWan region setting resilient to factory reset
1.9.0 (May 2021):
- Improve BLE scan robustness
- Maximize WiFi STM32 FW update success
- Earlier initialization of critical GPIOs
1.8.0 (February 2021):
- Support of multiple regional parameters.
- Use unconfirmed TX on LoRaWAN services.
- Wi-Fi update over HTTP.
- Access Point SSID personal identification based on EUI.
- Limit duration of Wi-Fi access point availability.
1.7.0 (June 2020):
- Initial release for Wanesy Wave.

Table of Contents