wiki:quickstart:quickstart_izepto_cellular
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
wiki:quickstart:quickstart_izepto_cellular [2022/07/29 10:06] ehe created |
wiki:quickstart:quickstart_izepto_cellular [2024/03/25 14:12] (current) ehe [Documentation] |
||
|---|---|---|---|
| Line 4: | Line 4: | ||
| ===== Documentation ===== | ===== Documentation ===== | ||
| - | * Leaflet (contains the list of accessories): {{ :documentation:commercial_leaflet_wirnet_izeptocell_cellular_v1.4.pdf |}}\\ | + | * Leaflet (contains the list of accessories): {{ :documentation:commercial_leaflet_wirnet_izeptocell_cellular_v3.4.pdf|}}\\ |
| - | * Quick start guide: {{ :documentation:e-dmk_-_quick_start_-_izepto_cellular_-_v1.0.pdf |}} | + | * Wanesy® Cellular Connectivity leaflet: {{ :documentation:wanesy-cellular_connectivity_commercial_leaflet_v1.0.pdf |}} |
| + | * Quick start guide: {{ :documentation:quick_start_guide_-_izeptocell_cellular_v2.pdf |}} | ||
| + | * Installation recommendations: {{ :documentation:an-klk03357_-_lorawan_gateways_installation_recommendations_-_v1.2.pdf | Gateways installation recommendations}} | ||
| ===== Zero Touch provisioning (ZTP) feature ===== | ===== Zero Touch provisioning (ZTP) feature ===== | ||
| - | The KerOS firmware integrates the Zero Touch provisioning (ZTP) feature. When you receive the gateway, you don’t need anymore to install software or to configure it, it is plug&play. | + | * [[wiki:systeme_mana:ztp|Zero Touch Provisioning (ZTP)]] |
| - | + | ||
| - | Supported configuration includes: | + | |
| - | * Connection to Kerlink Wanesy Management Center (WMC). | + | |
| - | * Chirpstack or TTN configuration. | + | |
| - | + | ||
| - | ZTP feature is available when the gateway boots for the first time with an available internet connection. | + | |
| - | + | ||
| - | <note warning>The gateway must remain powered up and connected to Internet during the entire ZTP process.</note> | + | |
| - | + | ||
| - | To enable ZTP on a gateway, it must be pre-declared on Kerlink ZTP Management server. | + | |
| - | Please contact Kerlink for more information at [[support@kerlink.fr]]. | + | |
| - | + | ||
| ===== Connection to the gateway ===== | ===== Connection to the gateway ===== | ||
| - | You can connect a PC directly to the Wirnet iZeptoCell with a USB cable. In this mode, the gateway will simulate an ethernet device. \\ | + | You can connect a PC directly to the Wirnet iZeptoCell **with a USB cable.** In this mode, the gateway will simulate an ethernet device. \\ |
| In nominal case, after few seconds, your PC will obtain an IP address and you will be able to start a SSH client or HTTP connection on gateway IP 192.168.120.1. \\ | In nominal case, after few seconds, your PC will obtain an IP address and you will be able to start a SSH client or HTTP connection on gateway IP 192.168.120.1. \\ | ||
| In particular case you are using a DHCP server on your computer, gateway will directly obtain an IP address. A connection can then be done on this IP address.\\ | In particular case you are using a DHCP server on your computer, gateway will directly obtain an IP address. A connection can then be done on this IP address.\\ | ||
| Line 32: | Line 22: | ||
| Once connected through USB cable, connection to the gateway can either be done via: | Once connected through USB cable, connection to the gateway can either be done via: | ||
| - | * SSH: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:connection_credentials#network_shell_access_ssh|click here]]. | + | * SSH: [[wiki:systeme_mana:connection_credentials#network_shell_access_ssh|click here]]. |
| - | * Web Interface: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:webui:zcel#Web Interface|click here]]. | + | * Web Interface: [[wiki:systeme_mana:webui:zcel#Web Interface|click here]]. |
| ===== Factory reset ===== | ===== Factory reset ===== | ||
| - | If needed the factory reset of the gateway is feasible. Consult the stock restore process: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:systeme_mana:features#stock_restore|click here]] | + | If needed the factory reset of the gateway is feasible. Consult the stock restore process: [[wiki:systeme_mana:features#stock_restore|click here]] |
| ===== Get the logs ===== | ===== Get the logs ===== | ||
| - | To simplify the log gathering process, Kerlink developed automatic log gathering methods. Consult the Automatic log gathering chapter: [[https://wikikerlink.fr/wirnet-productline/doku.php?id=wiki:support:troubleshoot#automatic_log_gathering|click here]] | + | To simplify the log gathering process, Kerlink developed automatic log gathering methods. Consult the Automatic log gathering chapter: [[wiki:support:troubleshoot#automatic_log_gathering|click here]] |
| ===== Connect an iZeptoCell to WMC ===== | ===== Connect an iZeptoCell to WMC ===== | ||
| Line 56: | Line 46: | ||
| You can register for Wiki update notifications by clicking on the envelope icon (“Manage subscriptions”) on the right side of the page. | You can register for Wiki update notifications by clicking on the envelope icon (“Manage subscriptions”) on the right side of the page. | ||
| + | ===== Administrative information ===== | ||
| + | [[https://wikikerlink.fr/faq/doku.php?id=home#administrative_information|Administrative information]] | ||
wiki/quickstart/quickstart_izepto_cellular.1659081980.txt.gz · Last modified: 2022/07/29 10:06 by ehe
