• BLE Asset Monitoring

• LoRaWan region setting resilient to factory reset

• BLE scan parameters update dead-end
• Unblock LoRaWan when in busy stack state
• ESP32 deadlocks detection

• If the installed firmware is 1.8.0 or lower, firmware upgrade procedure must respect specific order described in section below.

This release is compatible with the following Wanesy Wave revision:

• Wanest Wave 868:
  • Fully compatible with Wanesy Wave Board ID xxxDAcxxxxxx, xxxDAdxxxxxx, xxxDAexxxxxx.
• Wanesy Wave 915:
  • Fully compatible with Wanesy Wave Board ID xxxDBcxxxxxx, xxxDBdxxxxxx, xxxDBexxxxxx, xxxDBfxxxxxx .

• STM32 MCU firmware Ver. 2.0.1
• ESP32 MCU firmware Ver. 2.0.1

STM32 MCU :
To update the firmware, follow instruction on the Firmware update section of the Setup page: click here.

ESP32 MCU:
To update the firmware, follow instruction on the Firmware update section of the Setup page: click here.

Regular firmware update can be followed (update ESP32 first), please read e-con-wanesy_wave_fw_update_wifi_v1.2.pdf available in the Wanesy™ Wave Setup: Documentation section.

If the installed firmware is v1.8.0 or lower version, firmware update procedure must respect the specific order described below (update STM32 first):

• Wanesy Wave 868: wifiupdate_wanesywave_eu868_v2.0.1_20211005_revs_cde.zip
  • STM32 file: stm32_wanesywave_EU868_v2.0.1_DAcde.kbin (md5: 3664abb6d9f17425ca10a8ac7117e0a7).
  • ESP32 file: esp32_firmware_v2.0.1.bin (md5: 164e005e7453b7a7ee660fa973b2c437).

• Wanesy Wave 915: wifiupdate_wanesywave_us915_v2.0.1_20211005_revs_cdef.zip
  • STM32 file: stm32_wanesywave_US915_v2.0.1_DBcdef.kbin (md5: 3bf899586556161ca71fff4fc08c2c94).
  • ESP32 file: esp32_firmware_v2.0.1.bin (md5: 164e005e7453b7a7ee660fa973b2c437).

• Wanesy Wave 868: region_conf_wifiupdate_wanesywave_868_v1.8.0_20210421_revs_cde.zip
  • cmd_region_EU868.txt
  • cmd_region_IN865.txt

• Wanesy Wave 915: region_conf_wifiupdate_wanesywave_915_v1.8.0_20210421_revs_cdef.zip
  • cmd_region_US915.txt
  • cmd_region_AU915.txt
  • cmd_region_AS923.txt

• 2.0.1 (October 2021):
  • BLE Asset Monitoring
  • LoRaWan region setting resilient to factory reset
• 1.9.0 (May 2021):
  • Improve BLE scan robustness
  • Maximize WiFi STM32 FW update success
  • Earlier initialization of critical GPIOs
• 1.8.0 (February 2021):
  • Support of multiple regional parameters.
  • Use unconfirmed TX on LoRaWAN services.
  • Wi-Fi update over HTTP.
  • Access Point SSID personal identification based on EUI.
  • Limit duration of Wi-Fi access point availability.
• 1.7.0 (June 2020):
  • Initial release for Wanesy Wave.