• Support of multiple regional parameters: EU868, IN865, US915, AS923, AU915.
• Dynamic configuration of region.
• Use unconfirmed TX on LoRaWAN services.
• Add possibility to change LoRaWAN frame period by configuration.
• Introducing the CBOR configuration file device.cfg, to get and post parameters values.
• Add UUID iBeacon filter.
• Possibility to identify BLE Tags with MAC address or Major/Minor.
• Wi-Fi updates over HTTP.
• Wi-Fi access point SSID based on EUI.
• Limit duration of Wi-Fi access point availability to 45 cycles of BLE scan period.
• Add control of limit values for parameters.

• Avoid erroneous CBOR frame sent sometimes.
• Major/minor configuration is now persistant after a power cycle.

• Optout_klk SSID is used on the first boot after a factory reset command.
• Switching filter (mac address or major/minor ) can stop BLE radio transmission. Workaround is to trigger a remote reboot command or manual reboot.
• During configuration update, out of range values are replaced by “0”.

This release is compatible with the following Wanesy Wave revision:

• Wanest Wave 868:
  • Fully compatible with Wanesy Wave Board ID xxxDAcxxxxxx, xxxDAdxxxxxx, xxxDAexxxxxx.
• Wanesy Wave 915:
  • Fully compatible with Wanesy Wave Board ID xxxDBcxxxxxx, xxxDBdxxxxxx, xxxDBexxxxxx, xxxDBfxxxxxx .

• STM32 MCU firmware Ver. 1.8.0
• ESP32 MCU firmware Ver. 1.8.0

STM32 MCU :
To update the firmware, follow instruction on the Firmware update section of the Setup page: click here.

ESP32 MCU:
To update the firmware, follow instruction on the Firmware update section of the Setup page: click here.

• Wanesy Wave 868: wifiupdate_wanesywave_eu868_v1.8.0_20210205_revs_cde.zip
  • STM32 part file: stm32_wanesywave_EU868_v1.8.0_DAcde.kbin (md5: 0215506241d1f5d5451f63933b7c6e67).
  • ESP32 file: esp32-firmware_v1.8.0.bin (md5: e6306fdff81e62ebdb6d00690ae3de6a).

• Wanesy Wave 915: wifiupdate_wanesywave_us915_v1.8.0_20210205_revs_cdef.zip
  • STM32 part file: stm32_wanesywave_US915_v1.8.0_DBcdef.kbin (md5: 42692f4f3dab6bdefdb1fbb712453cf5).
  • ESP32 file: esp32_firmware_v1.8.0.bin (md5: e6306fdff81e62ebdb6d00690ae3de6a).

• Wanesy Wave 868: region_conf_wifiupdate_wanesywave_868_v1.8.0_20210421_revs_cde.zip
  • cmd_region_EU868.txt
  • cmd_region_IN865.txt

• Wanesy Wave 915: region_conf_wifiupdate_wanesywave_915_v1.8.0_20210421_revs_cdef.zip
  • cmd_region_US915.txt
  • cmd_region_AU915.txt
  • cmd_region_AS923.txt

• 1.8.0 (Frebuary 2021):
  • Support of multiple regional parameters.
  • Use unconfirmed TX on LoRaWAN services.
  • Wi-Fi update over HTTP.
  • Access Point SSID personal identification based on EUI.
  • Limit duration of Wi-Fi access point availability.
• 1.7.0 (June 2020):
  • Initial release for Wanesy Wave.