The connection to the Wanesy Management Center requires several software packages to be installed:

• Packet Forwarder and companion HAL: required to process LoRa packets.
• BSCC and SNMP: required to handle software upgrades, gateway monitoring, etc.
• OpenVPN package(s): required to establish the VPN between the gateway and the WMC
• An up-to-date firmware

To ease the process, a megapackage can be used to install or upgrade a gateway.

This megapackage includes all of these specific packages in an homogeneous way: a firmware, BSCC and SNMP components, a Packet Forwarder and its companion HAL.

This megapackage does not contain the OpenVPN package which is always delivered separately.

This megapackage preserves any change to your current network configuration (VPN and GSM/ETH configuration).

This megapackage can be used as well remotely (from WMC dashboard for instance) and locally (USB, debug link, SSH).

To make the process even easier, a magic link can be used to install or update your gateway. Follow this Magic Link

OpenVPN package(s) must be requested to support@kerlink.fr and installed on the gateway BEFORE using the megapackage.

By default, when installing the WMC embedded software, the IP configuration is DHCP.

If the gateway needs to have a specific configuration (static IP, mobile APN, etc), please refer to the specific FAQ - Static IP configuration section to know how to proceed:

Several methods are available to install the software on the gateway. The software and upgrade methods are list in the compatibility matrix below:

“Upgrade” stands for a gateway that is already connected to the WMC dashboard.

Embedded software can be delivered as one single megapackage or as individual packages. Please refer to the table below to pick the preferred method:

Notes:

1. For USB install/upgrade:
   1. a USB autorun script is required.
   2. follow the same procedure as for SSH
2. For SSH install/upgrade:
   1. On Wirnet Station, install the .tar.gz DOTA.
   2. On KerOS (iBTS and iFemtoCell), uncompress the .tar.gz TWICE (if applicable) and install the .ipk packages.
3. For individual packages (e.g. not the megapackage) on Wirnet Station, the firmware remote upgrade is not possible. Only BSCC, SNMP, Packet Forwarder and HAL can be installed over SSH/WMC. For firmware upgrades, please use USB.

This can be used to download a single software package (individual or megapackage) to the gateway.

Note that you should be connected to the WMC to use this feature.

1. Click on Management item and select Gateways item
2. Select your gateway,
3. Choose Configurations
4. Choose Software
5. Move your file in the drag and drop area in the right part of the page.

The workflows can be used to install software on several gateways at once.

Note that you should be connected to the WMC to use this feature.

To upgrade several gateways:

1. Click on Workflows from the main menu on the left side of the page to pull down the hidden menu
2. Select Templates
3. Click on the + to select the workflow template to use
4. Select the Category: Gateways
5. Drag and Drop the “updateGateways Firmware” template from “Available” window to “Selected” window
6. Give a name to your workflow: ex updateGateways
7. Click on Management item
8. Click on Gateways item
9. Click on the Cart icon on the left side of each line to add all the desired gateways to your cart (take care to group the same type of gateway: Wirnet iBTS or Wirnet iFemtoCell or Wirnet Station)
10. Select the Cart “Selection” at the upper side of your page
11. Choose the Execute workflow tab from the top menu.
12. Pull down the menu and pick up the updateGateways workflow you have just created
13. Choose the software package to download and execute the workflow by clicking the START button

For USB and SSH install and upgrade instructions, please find below an outlook of the procedures below.

* SSH (advanced user):

• Installation from scratch

   
  1. 	Copy the OpenVPN package in the /mnt/fuser-1/dota directory
  2. 	Reboot the gateway
  3. 	Wait the OpenVPN package installation
  4. 	Copy the megapackage in the /mnt/fuser-1/dota directory
  5. 	Reboot the gateway
  

• Upgrade

  1. 	copy the megapackage in the /mnt/fuser-1/dota directory 
  2. 	reboot the gateway

• Installation from scratch

      
  1. 	copy the OpenVPN package on your USB stick
  2. 	copy the produsb.sh file on your USB stick.
  3. 	Plug the USB stick on the gateway
  4. 	Wait for a few minutes that upgrade ends. 
  5. 	remove the USB stick from the gateway and erase the content.
  6. 	copy the megapackage on your USB stick
  7. 	copy the produsb.sh file on your USB stick
  8. 	Plug the USB stick on the gateway
  9.  	Wait for a few minutes that upgrade ends. 
  

• Upgrade

  
  1. 	copy the megapackage on your USB stick
  2. 	copy the produsb.sh file on your USB stick
  3. 	Plug the USB stick on the gateway
  4. 	Wait for a few minutes that upgrade ends
  

Only ipk files can be used.

If the megapackage is a .tar.gz file, please uncompress it to extract ipk files with the following command:

# Run on your computer
tar xzf *ran_gateway*.tar.gz

Then,

* SSH:

 
  1. Create the updates folder: mkdir -p /user/.updates
  2. Copy the .ipk files in /user/.updates/
  3. In the case of a first install,  copy the OpenVPN package(s) in /user/.updates/
  4. Run "sync" command
  5. Trigger the upgrade: kerosd –u
  6. Reboot the gateway

* USB:

  1. Copy .ipk files, openVPN package in the case of a first install
  2. Copy the usb.autorun and usbkey.txt files on the root directory of the USB stick
  3. Plug the USB stick to the gateway.
  4. Once the LED starts blinking, remove the USB stick and wait the end of upgrade (2').

Use the following command to check the currently installed packages (example shows iBTS):

root@klk-lpbs-123456:~ # opkg list-installed
bscc - v3.0.11                                   # <------ BSCC package version
kerlink-openvpn-config-pki2-klk-lpbs-060337 - 1.11-181221
keros - 3.4.5-0-g1d8781c3
libloragw2-fpga - 5.1.0-klk5
lorasnmp - v3.0.11                               # <------ SNMP package version
spf2 - 5.1.0-klk4_5.1.0-klk5
zconf-delete-gatewayid-lpbs - 1.0

Gateways running firmware « wirmaV2_wirgrid_v2.x » must be migrated to version « wirmaV2_wirnet_v3.1 » using the script create_dota_2x_wirnet3.sh .

Megapackage installation is only supported on firmware version « wirmaV2_wirnet_v3.1 » and upper. Firmware version can be found in the result of the command « get_version -u –v » via SSH or debug probe (see below).

[root@Wirnet_080E0761 ~]# get_version -u -v
KERNEL_VER=3.10.104-3.10.104-klk7
PIC_VER=8.3
BOOTSTRAP_VER=""
UBOOT_VER="U-Boot 2009.03-2009.03-klk1 (Jan 26 2018 - 12:04:27)"
SCRIPT_VER=v1.0
INITRAMFS_VER=v1.3
FILESYSTEM_VER=2016.05v1.10
KNETD_VER="wirma2_v4.09 WAN_3.16 (Dec 23 2016-14:33:40)"
PROD_FW=wirmaV2_wirnet_v3.1
LORABOARD_MANUFACTURER=00
LORABOARD_TYPE="868-27dBm"
LORABOARD_HWVERSION=05
LORABOARD_SERIALNO=000E3F
 
************************ Update log ************************
2019.03.05-17:17:55 -- Dota dota_RAN_gateway_v3.0.10_5e546851-f7a3-4881-a905-03a937a8d7e4.tar
2019.03.05-17:18:54 -- Dota custo_libloragw-fpga_4.1.3-klk8_wirnet.tar
2019.03.05-17:19:05 -- Dota custo_openvpn.tar
2019.03.05-17:19:10 -- Dota dota_packages_v3.0.10.tar
2019.03.05-17:20:07 -- Dota custo_libloragw-fpga_4.1.3-klk8_wirnet.tar
2019.03.05-17:20:18 -- Dota dota_spf_3.1.0-klk16_4.1.3-klk8_wirnet.tar
2019.03.05-17:20:26 -- Dota dota_v3.0.10_bscc.tar                        # <---- BSCC package version
2019.03.05-17:20:33 -- Dota dota_v3.0.10_snmp.tar                        # <---- SNMP package version
************************************************************
[root@Wirnet_080E0761 ~]#

Firmware version verification can be done by checking the trustable field « FILESYSTEM_VER ».

• FILESYSTEM_VER=2016.05v1.5 ⇒ firmware wirmaV2_wirnet_v3.1
• FILESYSTEM_VER=2016.05v1.10 ⇒ firmware wirmaV2_wirnet_v3.3
• FILESYSTEM_VER=2016.05v1.13 ⇒ firmware wirmaV2_wirnet_v3.6

For a first install, the gateway must be declared on the dashboard. Please refer to the administration documentation.